Results 1 to 7 of 7
  1. #1
    t00nces2 started this thread.
    t00nces2's Avatar
    SMF Badges of Honor


    Member since
    Jul 2014
    Location
    Sarasota, FL
    Posts
    1,707
    Thanks
    1,191
    Thanked 2,350 Times in 964 Posts

    Anyone Here Still Buying Computer Scrap?

    Been a while since I have dropped by or posted. The board seemed to stop for a while. I hope everyone is well.

    Anyway, I have a bunch of computer scrap and electronic scrap I want to get rid of and I am hoping someone here is buying boards and Ram and processors. I don't have a ton, so I am hoping there is someone around me I can take it to in the Tampa Bay area of Florida.

    Just got some Frontier cable boxes and I was wondering if they were worth tearing apart or if I should just toss them in with shred...





  2. #2
    CopperMiner's Avatar
    SMF Badges of Honor


    Member since
    Jun 2021
    Location
    Greater Montreal
    Posts
    320
    Thanks
    181
    Thanked 203 Times in 119 Posts
    Some of the scrap yards I deal with have a specific price for cable boxes, but it is close to shred price. Computers have a bit better price, but it is still way better to tear them apart. Among the other board and ewaste buyers that come to my mind, you should check out boardsort.com.

  3. #3
    greytruck's Avatar
    SMF Badges of Honor



    Member since
    Jan 2012
    Location
    Thornton, Illinois
    Posts
    1,909
    Thanks
    1,679
    Thanked 1,772 Times in 919 Posts
    Shred the cable box's.... unless theres a HDD in there, pull the HDD and then shred the rest.

  4. #4
    SMF Badges of Honor


    Member since
    Jun 2017
    Location
    Las Vegas
    Posts
    1,306
    Thanks
    3,232
    Thanked 1,921 Times in 785 Posts
    Closest place I personally know to you is Jacksonville Metal Recycling (Brett and Scott there can help you) that pays ok for e-waste. They should be paying at least .25/lb for cable boxes w/o hard drive. If you were anywhere near me I'd pay you .40 for them but it's too far to ship in anything less than large quantities.

  5. #5
    mikeinreco's Avatar
    SMF Badges of Honor


    Member since
    Dec 2011
    Location
    TENNESSEE
    Posts
    4,985
    Thanks
    1,257
    Thanked 5,023 Times in 2,351 Posts
    Yea you shouldn't send those cables boxes to shred....gold and copper way up boards should be worth between $2/$3 lb

  6. The Following User Says Thank You to mikeinreco for This Post:


  7. #6
    hills's Avatar
    SMF Badges of Honor



    Member since
    Sep 2017
    Location
    Maine
    Posts
    1,525
    Thanks
    824
    Thanked 1,354 Times in 786 Posts
    It's good to hear from you T. I hope all is well with you and your lady. How's the chess going ?

    The ewaste has dropped off a lot in this area over the last few years. I used to get a lot of satellite TV boxes and a few cable TV boxes here and there. The boards are about the same. They're well worth doing in my opinion. The local yard pays .30/lb. I usually ship them off to one of the ewaste buyers here and get around 3.00$/lb.

    What you want to do is focus on the green board. The tan colored board to the left on the one you pictured is the power board. That changes the voltage over from 120 volts to 12 volts. The power boards don't have much value so you can just toss them in with the sheet metal shred.

    Once the green board is out ... remove the aluminum heat sinks. They usually go as extruded ali.

    The hard drive ... if it comes with one ... is probably worthless. Nine times out of ten they either failed or are about to fail. The Western Digital greens have an especially high failure rate. It's generally best to pull the little green board on the back and toss the rest in with your aluminum shred.

    Anyhow ... save up your green boards in the shop. They don't take up much space. Ship em' out to an ewaste buyer here once you've accumulated 45 lbs and you'll probably do okay.

  8. The Following User Says Thank You to hills for This Post:


  9. #7
    SMF Badges of Honor

    Member since
    Nov 2021
    Location
    Canada
    Posts
    7
    Thanks
    0
    Thanked 0 Times in 0 Posts
    Yeah, while working on some electronic devices, I also came across some electronic scarps that might be sometimes minor or bigger ones. This occurrence of the huge number of electronic scrap is difficult for my working atmosphere. So for temporary scrap storage, I just used some disposal bins. You can also store the Frontier cable boxes while removing all the working parts on the bin and wait for the e-waste removal service to pickup.


  10. Similar threads on the Scrap Metal Forum

    1. International - Buying Computer Components for more than scrap value
      By KayleeSecureData in forum Scrap Buyers & Sellers
      Replies: 0
      Last Post: 07-13-2020, 12:56 PM
    2. National - Buying Computer Scrap,Laptops and LCD's
      By gorven in forum Scrap Buyers & Sellers
      Replies: 133
      Last Post: 05-28-2020, 08:04 AM
    3. Need some help on buying computer scrap
      By spoiler73 in forum A Day in the Life of a Scrapper
      Replies: 12
      Last Post: 07-30-2012, 09:01 PM

Thread Information

Users Browsing this Thread

There are currently 1 users browsing this thread. (0 members and 1 guests)

 
Browse the Most Recent Threads
On SMF In THIS CATEGORY.





OR

Bookmarks

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •  

The Scrap Metal Forum

    The Scrap Metal Forum is the #1 scrap metal recycling community in the world. Here we talk about the scrap metal business, making money, where we connect with other scrappers, scrap yards and more.

SMF on Facebook and Twitter

Twitter Facebook