Results 1 to 11 of 11

pick up: 67 impalla and our newly fabricated trailer

| A Day in the Life of a Scrapper
  1. #1
    Russell started this thread.
    Russell's Avatar
    SMF Badges of Honor

    Member since
    Jan 2012
    Location
    Chicago,Il
    Posts
    815
    Thanks
    495
    Thanked 707 Times in 324 Posts

    pick up: 67 impalla and our newly fabricated trailer

    Picked up our newly fabricated trailer. Back hauled this 67 impalla that was almost junked. 500$ got the car which needs a full restoration. We figured we couldn't loose no matter which direction we go with it.

    The new sides on the trailer are soiled as a rock the welder did a great job and we've made a great contact for future projects.



  2. #2
    gustavus is offline Metal Recycling Entrepreneur
    gustavus's Avatar
    SMF Badges of Honor


    Member since
    Sep 2011
    Location
    Canada
    Posts
    1,209
    Thanks
    1,351
    Thanked 920 Times in 425 Posts
    Nicely built trailer but the axles are located dead center of the deck, this arrangement will cause the trailer to wig wag at higher speeds on pavement but more pronounced on gravel roads.

    On the trailer below you will notice that the axles are placed about 2/3rds towards the rear of the deck.


  3. #3
    DiamondN's Avatar
    SMF Badges of Honor


    Member since
    Oct 2012
    Location
    Indiana
    Posts
    912
    Thanks
    2,150
    Thanked 378 Times in 243 Posts
    Those old Impalas are getting scarce. I don't think you'll have any problem finding a buyer. Thanks for saving it...

  4. #4
    SMF Badges of Honor



    Member since
    Feb 2012
    Location
    OK
    Posts
    5,731
    Thanks
    6,815
    Thanked 3,465 Times in 1,990 Posts
    nice!

  5. #5
    ilovejunk's Avatar
    SMF Badges of Honor


    Member since
    Jun 2011
    Location
    bear creek, nc
    Posts
    163
    Thanks
    112
    Thanked 227 Times in 67 Posts
    to bad your so far away i have a fire breathing 454 big block that would be right at home in that impala,

    and just for kicks id leave the car in as found condition and go school some ricers and fox body mustangs on how old school iron can run if its leaned on hard enough.

  6. #6
    PartTimeScrapper's Avatar
    SMF Badges of Honor



    Member since
    Aug 2011
    Location
    Morrison, Colorado
    Posts
    3,400
    Thanks
    1,004
    Thanked 3,256 Times in 1,335 Posts
    Im more concerned about the tow vehicle. Is that an explorer? You might want to consider upgrading your truck to something with a little more beef to it before you do to much hauling if that is an explorer. Cant really tell from picture.

  7. #7
    Mechanic688's Avatar
    SMF Badges of Honor



    Member since
    Mar 2011
    Location
    Warsaw , Ind. In the heart of the lakes, and down the street from the hotel where Al Capone stayed.
    Posts
    9,568
    Thanks
    11,247
    Thanked 10,730 Times in 4,728 Posts
    Quote Originally Posted by PartTimeScrapper View Post
    Im more concerned about the tow vehicle. Is that an explorer? You might want to consider upgrading your truck to something with a little more beef to it before you do to much hauling if that is an explorer. Cant really tell from picture.
    Yea, that ones an Explorer with a 4 way pallet on the roof.
    P & M Recycling - Specializing in E-Waste Recycling.
    If you enjoy your freedom, thank a vet.

  8. #8
    Russell started this thread.
    Russell's Avatar
    SMF Badges of Honor

    Member since
    Jan 2012
    Location
    Chicago,Il
    Posts
    815
    Thanks
    495
    Thanked 707 Times in 324 Posts
    Yes an explorer, that's what we have as of now. Is it ideal? No, does it work? Yes. Is it beating up the motor and trans? Yes. Do we plan on getting a better vehicle in the future? Yes. Is it a bit silly? Perhaps. Is that a four way pallet on the roof? Yes, its a few dollars closer to buying a new vehicle.

    I'd be more concerned about the guys on here that scrap in their cars and claim to fit a thousand pounds in their trunk. We've pulled over 20 tons (seperate loads) with her. She's been loyal and has paid for herself, my S-10 &and that trailer have also more than paid for themselves.

  9. The Following User Says Thank You to Russell for This Post:


  10. #9
    SMF Badges of Honor

    Member since
    May 2012
    Location
    central florida
    Posts
    139
    Thanks
    5
    Thanked 46 Times in 29 Posts
    got a title on that Impala? I know a guy in Ocala fl that's way into them.

  11. #10
    Russell started this thread.
    Russell's Avatar
    SMF Badges of Honor

    Member since
    Jan 2012
    Location
    Chicago,Il
    Posts
    815
    Thanks
    495
    Thanked 707 Times in 324 Posts
    Yes jaydee we do. We have an interested buyer. He's all the way in Montana. I'm not sure if we are going to work with him or look for someone else. PM with his or your info/ thanks.

  12. #11
    SMF Badges of Honor

    Member since
    Feb 2012
    Location
    Massachusetts
    Posts
    351
    Thanks
    145
    Thanked 105 Times in 79 Posts
    Thats what scrapping is all about, use what you have.

    On another forum, a member had trailer shake at speed, he ended up extending the tongue as a easy fix.
    If done properly it will still be strong. Again this is only if you have the wig wag at speed.


  13. Similar threads on the Scrap Metal Forum

    1. Trailer Brand names. Looking for a Tandem Axle trailer for Scrapping.
      By Kochy in forum Scrap Metal Tips and Advice
      Replies: 14
      Last Post: 08-26-2014, 12:40 AM
    2. last week trailer stollen this week new trailer for free
      By mrvictor1 in forum A Day in the Life of a Scrapper
      Replies: 8
      Last Post: 05-16-2013, 03:34 PM
    3. Replies: 11
      Last Post: 08-23-2012, 12:19 PM
    4. pick up bed trailer
      By taterjuice in forum Tools and Equipment
      Replies: 27
      Last Post: 06-20-2012, 09:23 PM
    5. is this a newly constructed forum
      By tjtat in forum Off Topic Discussions
      Replies: 2
      Last Post: 04-28-2011, 02:30 AM

Thread Information

Users Browsing this Thread

There are currently 3 users browsing this thread. (0 members and 3 guests)

 
Browse the Most Recent Threads
On SMF In THIS CATEGORY.





OR

Bookmarks

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •  

The Scrap Metal Forum

    The Scrap Metal Forum is the #1 scrap metal recycling community in the world. Here we talk about the scrap metal business, making money, where we connect with other scrappers, scrap yards and more.

SMF on Facebook and Twitter

Twitter Facebook