Results 1 to 11 of 11

Antique welder

| A Day in the Life of a Scrapper
  1. 01-22-2013, 11:00 AM #1
    Immulmen
    Immulmen is offline
    Immulmen started this thread.
    Immulmen's Avatar
    SMF Badges of Honor
    Member since
    Dec 2011
    Location
    Windham Maine
    Posts
    284
    Thanks
    13
    Thanked 272 Times in 117 Posts

    Antique welder

    I bought an antique welder last weekend for $75. It had 18 plugs on it to adjust the amperage, not a dial. I took it apart this morning and it was not as hard as I thought it would be. After taking the transformers out it took about 15 min of banging and prying to get the steel off the windings. They where just sandwiched together.
    Copper windings from 2 transformers 65 pounds.
    1 stripped cable [the insulation was falling apart] 11 pounds
    1 longer cable [I did not strip yet, the insulation is good so I may try to sell and it as is] 27 pounds
    18 brass plugs for plugging the cables into at 3 oz each + a few other fitting that came with it.



    Close to 100 pounds of copper. Not bad. I think I will watch for these. I know to stay away from the "tombstone" and newer welders with Aluminum windings.
    Chris
    Register to reply. Register To Reply
  2. 01-22-2013, 11:00 AM

  3. 01-22-2013, 11:56 AM #2
    freonjoe
    freonjoe is offline
    SMF Badges of Honor
    Member since
    Nov 2011
    Location
    boise, ID
    Posts
    1,605
    Thanks
    469
    Thanked 1,462 Times in 668 Posts
    Do you have a picture of the welder before you tore it down?
    http://www.scrapmetalforum.com/scrap...xid=Washington
  4. 01-22-2013, 12:01 PM #3
    Immulmen
    Immulmen is offline
    Immulmen started this thread.
    Immulmen's Avatar
    SMF Badges of Honor
    Member since
    Dec 2011
    Location
    Windham Maine
    Posts
    284
    Thanks
    13
    Thanked 272 Times in 117 Posts
    I don't have photos but it was somewhat like the one in this link.
    220vollt Forney Arc Welder/Brazer/Battery Charger - $125 (Windham, Maine)
  5. 01-22-2013, 12:11 PM #4
    freonjoe
    freonjoe is offline
    SMF Badges of Honor
    Member since
    Nov 2011
    Location
    boise, ID
    Posts
    1,605
    Thanks
    469
    Thanked 1,462 Times in 668 Posts
    Good score! Are you going to pick up the CL one too?
  6. 01-22-2013, 12:40 PM #5
    Immulmen
    Immulmen is offline
    Immulmen started this thread.
    Immulmen's Avatar
    SMF Badges of Honor
    Member since
    Dec 2011
    Location
    Windham Maine
    Posts
    284
    Thanks
    13
    Thanked 272 Times in 117 Posts
    I offered $75 and he just replied with $100. It is in the same town as I live so I think I will buy it.
    Chris
  7. 01-22-2013, 01:33 PM #6
    freonjoe
    freonjoe is offline
    SMF Badges of Honor
    Member since
    Nov 2011
    Location
    boise, ID
    Posts
    1,605
    Thanks
    469
    Thanked 1,462 Times in 668 Posts
    Good luck!
  8. 01-22-2013, 03:14 PM #7
    scrappy888
    scrappy888 is offline LowLife
    SMF Badges of Honor
    Member since
    Feb 2012
    Location
    Minneapolis
    Posts
    593
    Thanks
    324
    Thanked 324 Times in 171 Posts
    Very nice...have to keep my eyes open...never had the chance to break one apart...definitely seems worthwhile..thx
  9. 01-22-2013, 05:40 PM #8
    NWOdrudge
    NWOdrudge is offline Metal Recycling Entrepreneur
    SMF Badges of Honor
    Member since
    Dec 2012
    Location
    Florida
    Posts
    123
    Thanks
    113
    Thanked 72 Times in 45 Posts
    did a quick search on CL and everyone around here wants a gazillion dollars for theirs... 100lbs copper? gr8 score!
  10. 01-22-2013, 05:49 PM #9
    Immulmen
    Immulmen is offline
    Immulmen started this thread.
    Immulmen's Avatar
    SMF Badges of Honor
    Member since
    Dec 2011
    Location
    Windham Maine
    Posts
    284
    Thanks
    13
    Thanked 272 Times in 117 Posts
    Quote Originally Posted by NWOdrudge View Post
    did a quick search on CL and everyone around here wants a gazillion dollars for theirs... 100lbs copper? gr8 score!
    Picking up the other one in my link above tomorrow night. Be careful, a lot of the new ones have Aluminum transformers.
    I unwound the big transformer, the wingdings are flat bar shaped and the weight of the copper is 91 pounds.
    Chris

  11. The Following User Says Thank You to Immulmen for This Post:

    NWOdrudge
  12. 01-22-2013, 06:33 PM #10
    NWOdrudge
    NWOdrudge is offline Metal Recycling Entrepreneur
    SMF Badges of Honor
    Member since
    Dec 2012
    Location
    Florida
    Posts
    123
    Thanks
    113
    Thanked 72 Times in 45 Posts
    Quote Originally Posted by Immulmen View Post
    Be careful, a lot of the new ones have Aluminum transformers.
    Chris
    had to post.


    anyway, to the point. found this guys channel after you told me how much copper was in these machines. i don't know anything about welders but this guy does. reading the comments on his vids you can gain some info on which brands are crap. from my extremely tiny bit of experience, any machine that is crap should have much less copper.
    for those (like myself) that have no knowledge of these machines, the comment section of experienced welders might be useful info... perhaps, but entertaining at the least.
    Last edited by NWOdrudge; 01-22-2013 at 06:37 PM.
  13. 03-09-2013, 12:50 PM #11
    kbob
    kbob is offline
    SMF Badges of Honor
    Member since
    Jan 2012
    Posts
    218
    Thanks
    130
    Thanked 158 Times in 60 Posts
    Bought a older Forney welder and charger model# D 130 single phase.Unit had al.front and back covers.
    I do not know if there is any coralation with the covers and transformers,but tranformers were aluminum also.
    The power cord was 50 ft.of 10-3. Hoping to sell on C.L. and break even. Unit did not have any leads.
    Register to reply. Register To Reply

    14. Similar threads on the Scrap Metal Forum

    1. Does anyone use a welder to cut metal?
      By newattitude in forum Tools and Equipment
      Replies: 11
      Last Post: 01-27-2014, 07:03 PM
    2. Texas | Items Wanted - wanted - Antique safe
      By easyrecycle in forum Scrappers Classifieds
      Replies: 7
      Last Post: 04-22-2013, 11:08 PM
    3. scrapping a welder-any advice?
      By pwa in forum Scrap Metal Questions and Answers
      Replies: 12
      Last Post: 05-15-2012, 08:27 AM
    4. OT: Antique bottles?
      By ilyaz in forum More than Scrap Value
      Replies: 20
      Last Post: 11-04-2011, 04:15 PM
    5. antique sewing machine
      By spoiler73 in forum A Day in the Life of a Scrapper
      Replies: 15
      Last Post: 10-06-2011, 02:45 AM

« They Know I'm A Scrapper! | Todays load,Payday. »

Thread Information

Users Browsing this Thread

There are currently 1 users browsing this thread. (0 members and 1 guests)

 
Browse the Most Recent Threads
On SMF In THIS CATEGORY.




OR

Bookmarks

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •  

Forum Rules


The Scrap Metal Forum

    The Scrap Metal Forum is the #1 scrap metal recycling community in the world. Here we talk about the scrap metal business, making money, where we connect with other scrappers, scrap yards and more.

SMF Recommended Links

SMF on Facebook and Twitter

Twitter Facebook