Metal Recycling Entrepreneur
|
This batch is for the newbe with microwaves I don't bother with screw drivers . Hammers or my fav like this wrecking hammer & some clippers .
The side of microwave with fan is the side you want open . Slam the screws and peel the side open pound out the transformer - small fan - cut wires - control buttons are copper bearing - as is the magnetron . Wires- and small motor for glass round tray . MW’s are a decent find .
Last edited by Copper Head; 06-20-2013 at 02:08 AM.
Metal Recycling Entrepreneur
|
|
this is the goods
|
And while your doing all that slamming and banging watch out for that beryllium. It's either white or pink.
Don't break it or breathe it. Very bad for your health.
P & M Recycling - Specializing in E-Waste Recycling.
If you enjoy your freedom, thank a vet.
Metal Recycling Entrepreneur
And when you're done, you can pack the inside with small stuff and maximize your load. I love getting microwaves, you can strip them down fast after you've done a couple, and they have a good bit of copper in 'em.
Metal Recycling Entrepreneur
|
|
Well glad to here that , I'll be careful around that spot ,usually i'll just pull that little bit of brass from area.Originally Posted by Mechanic688
And while your doing all that slamming and banging watch out for that beryllium. It's either white or pink.
Don't break it or breathe it. Very bad for your health.
|
I would still use a drill or screwdriver to open and gut them, much safer that way.
NOBODY will buy the magnatrons around hereso I have to throw them away.
dont forget the small motor on the bottom - open the little flap and get that one too
|
the round magnets on the magnetron do well on ebay, plus the aluminum fins and brass washers on the magnetron come off easily also
I buy and sell all types of scrap and escrap. I buy specialty and hard to sell escrap. I buy resale items. PM me or contact me at jghilino@hotmail.com
I AM ACTIVELY BUYING ESCRAP OF ALL TYPES. BOARDS, RAM, CPUS AND MUCH MORE
Metal Recycling Entrepreneur
|
|
That sounds whacked - There copper bearing - find a yard who will take them or box em up sell them on E bayI would still use a drill or screwdriver to open and gut them, much safer that way.
NOBODY will buy the magnatrons around here
dont forget the small motor on the bottom - open the little flap and get that one too
Metal Recycling Entrepreneur
my magnatrons go with my electric motors
Metal Recycling Entrepreneur
i've got a stack of those magnets i keep meaning to drop off at the yard sometime
|
i found half copper half alum on trandformer. i only scraped two. so what part is hazardous?
|
|
Look at the pic, it's down on the snout (slender) part, can be a couple of different colors. Usually pink and white are the most common, I'll take that part off and wrap it up and dispose of it.watch out for that beryllium. It's either white or pink.
Metal Recycling Entrepreneur
|
Some microwave transformers have a Ali winding & a copper winding on the transformer. Normally they are the cheaper ones OR they are the sort of microwave that also has heating elements in it, like a normal oven has.
Theory being that a microwave uses all the power thats getting to it, but if you need some of that power for the elements, it gets taken from the magnatron, so the magnatron is down graded 30 odd percent.
The magnetron also has a very small amount of radioactive substance in it & it will set off the scrap dealers radiation dectectors. Same radioactive stuff as a gas lanterns mantle. Its not going to make you glow in the dark.
|
|
and if you keep banging around with those tools then you'll be able to post in this thread;
http://www.scrapmetalforum.com/off-t...-injuries.html
it just took me 10 min. to totally strip down one for the yard with a screwdriver.
-
Newbe 1st and 2nd loadThere are currently 3 users browsing this thread. (0 members and 3 guests)
|
Browse the Most Recent Threads
On SMF In THIS CATEGORY. 
OR 
|
Posting Permissions
Register To Reply
Bookmarks