As I have found most motors from washers are copper clad I have some sink disposers motors ,Sure i can dismantle but if some one can say that most disposers motors are copper clad I'll take your word on it.
Metal Recycling Entrepreneur
|
As I have found most motors from washers are copper clad I have some sink disposers motors ,Sure i can dismantle but if some one can say that most disposers motors are copper clad I'll take your word on it.
Experienced Scrapper
|
I have no idea but how about you take note of the model number then rip into it and post the results.
As soon as you can get to the windings scrape the coating off and take a look see. If it's copper finish 'er off!
Model numbers will often tell you what the windings of the motor are made of along with other manufactures information.
When the white man discovered this country Indians were running it
no taxes, no debt, women did all the work.
White man thought he could improve on a system like this. - Old Cherokee saying
I did not surrender, they took my horse and made him surrender. - Lone Watie
Metal Recycling Entrepreneur
|
|
Next time I'll try the INTERNET Model # search . I ended up searching with a sledge hammer, each one had a hefty amt of true copper . I have noticed with vac motors, i still have never found a Copper Clad. Maybe these type also .Originally Posted by injunjoe
-------------------
advantage to copper
Creep is the gradual deformation of a material from constant expansions and contractions under “load, no-load” conditions. This process has adverse effects on electrical systems: terminations can become loose, causing connections to heat up or create dangerous arcing. Copper does not creep or loosen at its connections. For other metal conductors that creep, extra maintenance is required to check terminals periodically and ensure that screws remain tightened to prevent arcing and overheating. These extra measures can be avoided with the use of copper wire.
-------------------------------------------
Coefficient of thermal expansion
Metals and other solid materials expand upon heating and contract upon cooling. This is an undesirable occurrence in electrical systems. Copper has a low coefficient of thermal expansion for an electrical conducting material. Aluminum, an alternate common conductor, expands nearly one third more than copper under increasing temperatures. This higher degree of expansion, along with aluminums lower ductility can cause electrical problems when bolted connections are improperly installed. By using proper hardware, such as spring pressure connections and cupped or split washers at the joint, it may be possible to create aluminum joints that compare in quality to copper joints
-------------------------------
Thermal conductivity
Thermal conductivity is the ability of a material to conduct heat. In electrical systems, high thermal conductivity is important for dissipating waste heat, particularly at terminations and connections. It is also important for reducing energy consumption due to the generation of waste heat.
Copper has a 60% better thermal conductivity rating than aluminum,so it is better able to reduce thermal hot spots in electrical wiring systems.
------------------------------
I suspect some applications might not be able to be copper clad
Last edited by Copper Head; 01-08-2012 at 07:42 PM.
Metal Recycling Entrepreneur
|
I wish you guys wouldn't use the words 'Copper clad'. That implies theres copper there.
Most of the Ali windings wire is just plain Ali with a copper toned varnish on it, or its anodized to that colour.
They are so easy to check, just jam a screwdriver into the wire & pick out a few strands from the coil & have a look at the ends.
Not actually removing the wire, just picking it out a bit.
Ali wire strands are very compliant, when you move it it takes no energy & stays where you left it.
Copper wire is stronger & bounces back a bit when you move it (with the screwdriver).
Metal Recycling Entrepreneur
|
|
AL with CU toned varnish lets call it to really confuse outsiders ALCUTV
Metal Recycling Entrepreneur
|
|
I am going to give it a try - Has any one ever hit upon a ALCUTV Vacuum motor.
There are currently 1 users browsing this thread. (0 members and 1 guests)
|
Browse the Most Recent Threads
On SMF In THIS CATEGORY. 
OR 
|
Posting Permissions
Register To Reply
Bookmarks