Results 1 to 7 of 7

my most efficiant e tear down.

| Dismantling, Breaking Down & Maximizing Scrap
  1. #1
    EcoSafe started this thread.
    EcoSafe's Avatar
    SMF Badges of Honor



    Member since
    May 2011
    Posts
    3,705
    Thanks
    3,713
    Thanked 6,807 Times in 1,954 Posts

    my most efficiant e tear down.

    if i'm dealing with pallet load or bigger towers or servers i have found a little extra time in front saves me a lot of time over all.

    I stack the load into like servers or towers.
    each make or even model can be a little different , diffrent screws rivets etc,

    a u 1 or u2 server is a whole different animal from a costom 300 pounder.

    by separating them into category you will b
    get a rithum and the proper bits tools etc together in one spot easy to access.

    doing them any other way causes tool searches and momentary thoughts trying to figure them out each causing a small delay in your task. those delays can add up to several hours over a weeks time.
    "anyone who thinks scrappin is easy money ain't doin it right!"

  2. The Following 2 Users say Thank You for This Post by EcoSafe:



  3. #2
    SMF Badges of Honor


    Member since
    May 2012
    Location
    SC - NC State Line
    Posts
    220
    Thanks
    50
    Thanked 120 Times in 76 Posts
    I totally agree with you OldDude. The more organixed you can be the better your chances are of making more $$ per hour. I try to arrange everything I do, so that it makes more sence to my way of thinking, which in turn makes my work load easier and often times much quicker.


    I wish you the best of luck with your upcoming surgeries. You will be in my prayers.

    Also, I want to thank you for your many pearls of wisdom here on the forum.


  4. The Following User Says Thank You to theelectronrecycler for This Post:


  5. #3
    SMF Badges of Honor



    Member since
    Jul 2011
    Location
    Jacksonville, NC
    Posts
    4,917
    Thanks
    15,632
    Thanked 5,861 Times in 2,713 Posts
    I agree also but I find I get bored easily so after 6-10 of one model I need to do something else. Luckily I have lots to do that is different that I wish were more repetative. Mike.
    "Profit begins when you buy NOT when you sell." {quote passed down to me from a wise man}

    Now go beat the copper out of something, Miked

  6. #4
    mikeinreco's Avatar
    SMF Badges of Honor


    Member since
    Dec 2011
    Location
    TENNESSEE
    Posts
    4,985
    Thanks
    1,257
    Thanked 5,023 Times in 2,351 Posts
    I agree.....One day I do towers, one day servers, one day printers, and when I get in the mood to sell sum copper monitors

  7. #5
    SMF Badges of Honor


    Member since
    Jul 2012
    Posts
    265
    Thanks
    31
    Thanked 186 Times in 87 Posts
    my downtime was having the toilet paper roll on the left side, I'm right handed so by moving
    the roll to the right, I can grab paper much quicker now, more time to scrap.

  8. The Following 3 Users say Thank You for This Post by scrapperben:


  9. #6
    Russell's Avatar
    SMF Badges of Honor

    Member since
    Jan 2012
    Location
    Chicago,Il
    Posts
    815
    Thanks
    495
    Thanked 707 Times in 324 Posts
    Now this is the kind if thread I like to see. Little bit of thinkin saves a lot of unnecessary doing.

  10. #7
    parrothead's Avatar
    SMF Badges of Honor


    Member since
    Jan 2011
    Location
    Treasure Coast, FL
    Posts
    2,416
    Thanks
    667
    Thanked 2,067 Times in 953 Posts
    I love having a stack of "like style" computers. It makes things so much nicer. I once had a stack of 50 laptops all the same. When I started I was at 15 minutes breaking my first one down. By the 4th one I was down to 3 minutes each and was on a rhthym.

    Just this weekend, I had 82 of an exact same model that I was breaking down. Not a full tower, but a "satellite" type unit. Not much to it. A power supply and a motherboard, a steel inner casing and a plastic 2 piece outer casing, all with a fairly nice possibly resellable splitter/adaptor cord off of the back. As usual the first one took some time. I needed to set up with a 3/16 bit to undo 6 screws on the back that held in the motherboard, and then I just needed a flat blade screwdriver to quickly undo the one screw that held in the power supply. Once the power supply was done I needed the flat blade to make one twist to remove the power supply and then one certain placement to then remove the mother board.

    After I got the routine down and was moving fairly quick I figured that I needed to do 4 units in 10 minutes in order to make $20 an hour. I grabbed 4 of them and kept at it now that I had the routine down. Finished them and looked at my clock and I was at 6 minutes. Sweet!. I kept going and cleaned up. In more ways than one.
    "64K should be enough for anybody." - Bill Gates 1981
    http://www.treasurecoastelectronicrecycling.com/

  11. The Following 5 Users say Thank You for This Post by parrothead:



  12. Similar threads on the Scrap Metal Forum

    1. 5.25 floppy drives...dont tear apart!
      By Ecycle Atlanta in forum Scrap Metal Questions and Answers
      Replies: 16
      Last Post: 08-21-2013, 11:33 AM
    2. Microwave Tear Down
      By CMHN in forum Scrap Metal Videos
      Replies: 17
      Last Post: 07-05-2013, 02:24 PM
    3. Should I tear it apart????
      By lastchance in forum Scrap Metal Tips and Advice
      Replies: 17
      Last Post: 03-30-2012, 09:23 PM
    4. LCD Monitor tear down
      By street_sweeper in forum General Electronics Recycling
      Replies: 8
      Last Post: 02-11-2012, 03:53 PM
    5. Starting a Mobile Home Tear Down
      By ocedy in forum Dismantling, Breaking Down & Maximizing Scrap
      Replies: 6
      Last Post: 09-20-2011, 10:18 PM

Thread Information

Users Browsing this Thread

There are currently 2 users browsing this thread. (0 members and 2 guests)

 
Browse the Most Recent Threads
On SMF In THIS CATEGORY.





OR

Bookmarks

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •  

The Scrap Metal Forum

    The Scrap Metal Forum is the #1 scrap metal recycling community in the world. Here we talk about the scrap metal business, making money, where we connect with other scrappers, scrap yards and more.

SMF on Facebook and Twitter

Twitter Facebook