Results 1 to 4 of 4

I'm sure some of the gurus have done this... Or is it a waste?

| Dismantling, Breaking Down & Maximizing Scrap
  1. 09-05-2011, 11:31 AM #1
    Evan_O
    Evan_O is offline Experienced Scrapper
    Evan_O started this thread.
    Evan_O's Avatar
    SMF Badges of Honor
    Member since
    Aug 2011
    Location
    Ft. Worth, TX
    Posts
    11
    Thanks
    3
    Thanked 0 Times in 0 Posts

    Question I'm sure some of the gurus have done this... Or is it a waste?

    This seems like it could be beneficial if it doesn't lower the total weight, scorch it if done wrong, etc.

    It's melting down copper wire into bars. I gathered this could make it all copper 1 and if you're someone that scraps often and has the torch and other supplies, and many pounds of copper wire, that this could be beneficial. I randomly found this on google and it's on ehow.com

    I searched and didn't find anything on it so maybe it's been discussed in the private forums or I didn't search properly.

    It peaked my interest so any opinions on this are welcome. I was googling how to remove the red look off some copper from a microwave so they don't count it as less because it looks kinda like the reddish glued copper under standard tv tubes. Anyway here's the link:

    http://www.ehow.com/how_8505171_melt...home-bars.html

    -Evan
    Last edited by Evan_O; 09-05-2011 at 11:33 AM. Reason: My OCD had to correct a grammatical error aka spelling
    Register to reply. Register To Reply
  2. 09-05-2011, 11:31 AM

  3. 09-05-2011, 02:02 PM #2
    Patton
    Patton is offline
    Patton's Avatar
    SMF Badges of Honor
    Member since
    Mar 2011
    Location
    Gilpin, CO
    Posts
    61
    Thanks
    10
    Thanked 21 Times in 12 Posts
    http://www.scrapmetalforum.com/showt...ghlight=ingots



    http://www.scrapmetalforum.com/showt...ghlight=ingots

    These are the two Threads that I know of.

    I took in a ingot to my yard and they would pay me insulated price. It is just that they do not know if there is any lead, alum., or other non copper elements in the ingot. If you can get the yard or e-bay buyers to buy it, and do not spend more than it is worth melting it.

    GO FOR IT!!

    I can not. So I just use the ingots as bullion for my other projects.
  4. 09-05-2011, 03:31 PM #3
    EcoSafe
    EcoSafe is offline
    EcoSafe's Avatar
    SMF Badges of Honor
    Member since
    May 2011
    Posts
    3,705
    Thanks
    3,713
    Thanked 6,807 Times in 1,954 Posts
    the shelacked wire from tubes and microwaves should go as #2 as is. The process to turn it into #1 Bullion is too expensive, dangerous and time consuming, unless you want to make ingots for retail sales. just my .o2. Gustove would be the one to talk to aqbout that.
  5. 09-05-2011, 05:32 PM #4
    CMHN
    CMHN is offline Experienced Scrapper
    CMHN's Avatar
    SMF Badges of Honor
    Member since
    Jul 2011
    Location
    Berwick, Pa
    Posts
    380
    Thanks
    49
    Thanked 339 Times in 111 Posts
    Its really not worth it if your just going to melt your scrap to take to the scrap yard. Most scrap yards wont buy ingots and those who do will pay you at a lower grade. Now if you want to get into sand casting, you could make stuff from your scrap and sell it for a much better profit. There are forums out there that are dedicated to this.


    If you really want to try it, you can melt lead, zinc, and aluminum in a steel crucible made from a large diameter pipe with a plate welded to the bottom. A campfire with an air supply will be enough to melt these metals.

    If you want to melt brass, bronze, and copper you will need a ceramic crucible and a pretty beefy furnace. Copper will melt at about 2500 degrees F I believe.

    Before you try to do this I would recommend that you do a Google search and read as much as you can about the subject, you can get hurt pretty badly if you are not careful.
    CMHN Recycling
    Register to reply. Register To Reply

  6. The Following User Says Thank You to CMHN for This Post:

    Dumpster-Dee

    7. Similar threads on the Scrap Metal Forum

    1. E waste
      By Copper Head in forum A Day in the Life of a Scrapper
      Replies: 21
      Last Post: 07-30-2012, 08:07 AM
    2. Any tech gurus out there?
      By parrothead in forum Off Topic Discussions
      Replies: 15
      Last Post: 04-22-2012, 11:48 AM
    3. flatline online for computer gurus
      By flatline in forum Introduce yourself
      Replies: 9
      Last Post: 12-12-2011, 09:41 AM
    4. question to all the vintage apple gurus
      By ilyaz in forum More than Scrap Value
      Replies: 0
      Last Post: 10-19-2011, 11:58 AM
    5. Need a Hot Line For the E Gurus
      By Kris Kringle in forum General Electronics Recycling
      Replies: 14
      Last Post: 08-22-2011, 10:58 PM

« transmissions | Steel Mills »

Thread Information

Users Browsing this Thread

There are currently 1 users browsing this thread. (0 members and 1 guests)

 
Browse the Most Recent Threads
On SMF In THIS CATEGORY.




OR

Tags for this Thread

Bookmarks

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •  

Forum Rules


The Scrap Metal Forum

    The Scrap Metal Forum is the #1 scrap metal recycling community in the world. Here we talk about the scrap metal business, making money, where we connect with other scrappers, scrap yards and more.

SMF Recommended Links

SMF on Facebook and Twitter

Twitter Facebook