Results 1 to 5 of 5
  1. #1
    TheRecycleGuy started this thread.
    TheRecycleGuy's Avatar
    SMF Badges of Honor

    Member since
    Jun 2013
    Location
    new iberia LA
    Posts
    342
    Thanks
    197
    Thanked 303 Times in 119 Posts

    What would you do with some of these boards and Grade type?

    mostly all have double sided gold fingers and some boards have lots of gold pin connectors, some all the way to the board . a couple of close up pictures im looking to see if they are tantalum cap? i have 48 photos in this link that are from a prison security system i recieved along with a trailer load of other goodies. yes that is a box of about 6 or 8 units of 911 dispatch panels. thanks for the help. oh by the way the yellow chips soddered like all the others, im guessing thats not tantalum neither..

    here is the link to the photos. https://www.dropbox.com/sh/vwz1dxavk...BpYRDS-ha?dl=0



  2. #2
    RLS0812's Avatar
    SMF Badges of Honor

    Member since
    Feb 2014
    Location
    Bucks County Pennsylvania
    Posts
    895
    Thanks
    155
    Thanked 633 Times in 358 Posts

    Exclamation

    Different buyers grade, and pay out, different amounts for boards.
    Get prices from several different folks, don't just go with the first offer you get.

    On a side not: some of that stuff is not sellable as-is unless you break it down ( lamps, relays, e.t.c. )
    Last edited by RLS0812; 06-03-2018 at 05:32 AM.

  3. The Following User Says Thank You to RLS0812 for This Post:


  4. #3
    eesakiwi's Avatar
    SMF Badges of Honor



    Member since
    Dec 2010
    Location
    NZ
    Posts
    2,531
    Thanks
    2,909
    Thanked 2,556 Times in 1,227 Posts
    Tantis normally have the positive pole (+) labeled. Other caps have the negative pole (-) labeled.

    The bigger yellow blocks are relays, look for the boards ink printing for that item 'RLY' or such. Those will have tiny 'Gold bar' contacts, probably Gold plated Silver bars.

  5. The Following User Says Thank You to eesakiwi for This Post:


  6. #4
    TheRecycleGuy started this thread.
    TheRecycleGuy's Avatar
    SMF Badges of Honor

    Member since
    Jun 2013
    Location
    new iberia LA
    Posts
    342
    Thanks
    197
    Thanked 303 Times in 119 Posts
    the lamps and relays was just shown for what i recieved from the pickup. every board has fingers (tall ones) and they are old boards. just curious if that type of quantity of fingered boards vs the downgrade of the board if i should trim them. Im sure the silver pieces i zoomed in on are tant caps the sister same cards have orange not silver ones. the orange bullet kind of piece that i think is tant cap to. but thanks for the info anyhow.

  7. #5
    RLS0812's Avatar
    SMF Badges of Honor

    Member since
    Feb 2014
    Location
    Bucks County Pennsylvania
    Posts
    895
    Thanks
    155
    Thanked 633 Times in 358 Posts
    Sprague 500D series
    Sprague 501D series

    Nether one is tantalum

    The ICs are worth a bit of money if you can carefully desolderer 'em
    Examples I seen:
    Motorola mc14538bcp
    Worth about $0.50 each
    Motorola mc14011bcp
    Worth about $0.60 each

    Some of the other parts are worth money such as the
    Aromat ds2e-m-dc12v relays
    Worth about $0.90 each

    Most of the boards have too much "heavy stuff" attached to them to be worth much to a buyer. The fingers can go for up to $2 an ounce last I looked, however it's going to take a few of them to make an ounce.

    trentech 130-01 remote switch card

  8. The Following User Says Thank You to RLS0812 for This Post:



  9. Similar threads on the Scrap Metal Forum

    1. Low grade/Brown boards vs Mid to high grade Green boards
      By newattitude in forum Low-Grade Electronics Recycling
      Replies: 2
      Last Post: 02-01-2014, 09:37 PM
    2. What would these boards grade at?
      By IdahoScrapper in forum E-Waste Grading and Identification
      Replies: 6
      Last Post: 12-07-2012, 03:16 PM
    3. What grade are these boards?
      By GeorgeB in forum E-Waste Grading and Identification
      Replies: 9
      Last Post: 12-01-2012, 11:54 PM
    4. Please grade/value these boards :o)
      By Enoch43 in forum E-Waste Grading and Identification
      Replies: 3
      Last Post: 05-27-2012, 12:15 PM
    5. Grade these boards
      By PartTimeScrapper in forum E-Waste Grading and Identification
      Replies: 5
      Last Post: 05-04-2012, 10:14 PM

Thread Information

Users Browsing this Thread

There are currently 1 users browsing this thread. (0 members and 1 guests)

 
Browse the Most Recent Threads
On SMF In THIS CATEGORY.





OR

Bookmarks

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •  

The Scrap Metal Forum

    The Scrap Metal Forum is the #1 scrap metal recycling community in the world. Here we talk about the scrap metal business, making money, where we connect with other scrappers, scrap yards and more.

SMF on Facebook and Twitter

Twitter Facebook