Results 1 to 18 of 18

Article: The Gold We All Search For.

| General Electronics Recycling
  1. #1
    Dunemaul started this thread.
    Dunemaul's Avatar
    SMF Badges of Honor



    Member since
    Nov 2011
    Location
    East Orlando FL
    Posts
    1,064
    Thanks
    157
    Thanked 560 Times in 301 Posts

    Article: The Gold We All Search For.

    Components from older computer chips, transistors, and electronics of the 1960's and 70's contain the most gold content. Their general purpose was for military and aerospace applications. Due to demanding conditions the components were required to use heavier gold plated caps (lids) and leads/pins/connectors. By using heavier amounts of precious metals the components could have and increased longevity and corrosion resistance.

    During the 1990's the best candidates for gold recovery, are the early versions of the Intel Pentium Processor, Intel Pentium Pro Processor, And many DEC Alpha (and similar RISC CPU's). Reason being that these chips had large gold plated caps, pins, and internal solid gold wiring.Very fine solid gold wiring, that typically was 99.9% pure gold, was used in wire bonding the computer chip (die) to the substrate package. Other components such as the cap, lids, pins, and pads are only gold plated. Something to be careful of is some manufacturers have also used aluminum wiring in the past in place of solid gold wiring to lower costs.

    The top dog for gold content during the 1990's hands down was the Pentium Pro. It has a large surface area of gold plated pins and cap. Under the cap you will find two separate chips, this doubles the amount of gold present compared to a single CPU.



    After 1998 we start to see a sharp decline in gold content of Cpu's. Reasons behind this was manufactures no longer used solid gold wire bonding technology or gold plated pins in their packaging. A good example is, the Intel Pentium 4 Microprocessor, which came in an organic package material with a metal lid and no gold wire. The only gold able to be extracted was from the pins. "The pins were gold plated with a thickness of only 0.76 microns, that calculates to only 0.000176 cc of gold per cpu".

    What we can expect from the future is already here and shows the dying age of gold recovery from cpu's. Today's processors have no connector pins, instead using a thinly gold plated connection pad to socket the Cpu to the motherboard.

    In the next article I will discuss processors that are worth more then their weight in gold and where some might be found. Happy treasure hunting.

    -Dunemaul
    Last edited by Dunemaul; 07-16-2012 at 05:11 AM.
    Born to think, destine to succeed.



  2. #2
    RuggedCountrySteve's Avatar
    SMF Badges of Honor

    Member since
    Jun 2012
    Location
    South East Manitoba, Canada
    Posts
    23
    Thanks
    22
    Thanked 17 Times in 10 Posts
    and now I know a little more. Thanks Dunemaul.

  3. #3
    SMF Badges of Honor


    Member since
    Feb 2012
    Location
    tampa
    Posts
    26
    Thanks
    5
    Thanked 6 Times in 5 Posts
    Thanks...Almost like a reliable WIKI page

  4. #4
    Dunemaul started this thread.
    Dunemaul's Avatar
    SMF Badges of Honor



    Member since
    Nov 2011
    Location
    East Orlando FL
    Posts
    1,064
    Thanks
    157
    Thanked 560 Times in 301 Posts
    Quote Originally Posted by grabinow View Post
    Thanks...Almost like a reliable WIKI page

    I need to practice for when i head back to college, so i figure I'd share small parts of the data that i have collected over the year. Only thing i can't say is true about the article is the section in quotes, and the big boys aint gonna say if the number is right or wrong.

  5. The Following 2 Users say Thank You for This Post by Dunemaul:


  6. #5
    SMF Badges of Honor

    Member since
    Sep 2011
    Location
    Rochester NY
    Posts
    615
    Thanks
    19
    Thanked 526 Times in 238 Posts
    can you link the orginal source?

    http://reclaimtech.com/
    We pay you to recycle!

  7. #6
    Dunemaul started this thread.
    Dunemaul's Avatar
    SMF Badges of Honor



    Member since
    Nov 2011
    Location
    East Orlando FL
    Posts
    1,064
    Thanks
    157
    Thanked 560 Times in 301 Posts

  8. The Following User Says Thank You to Dunemaul for This Post:


  9. #7
    Scrapcrazy's Avatar
    SMF Badges of Honor



    Member since
    Jul 2012
    Location
    Oklahoma
    Posts
    321
    Thanks
    153
    Thanked 321 Times in 125 Posts
    Good stuff Dunemaul! Thanks for the work and welcome back!

  10. The Following User Says Thank You to Scrapcrazy for This Post:


  11. #8
    BRASSCATCHER's Avatar
    SMF Badges of Honor


    Member since
    Feb 2012
    Posts
    2,476
    Thanks
    3,436
    Thanked 3,965 Times in 1,383 Posts
    Thanks Dune...read the rest of article and learned something new today....thanks again.
    I won't be wronged. I won't be insulted. I won't be laid a-hand on. I don't do these things to other people, and I require the same from them.” John Wayne-- The Shootist

    NEWBS READ THIS THREAD ABOUT REFINING!!!!
    http://www.scrapmetalforum.com/off-t...ning-read.html

  12. #9
    Dunemaul started this thread.
    Dunemaul's Avatar
    SMF Badges of Honor



    Member since
    Nov 2011
    Location
    East Orlando FL
    Posts
    1,064
    Thanks
    157
    Thanked 560 Times in 301 Posts
    Yeah im working on using part of the 2nd section of the article and incorporating items that i have found through research that contain the rare chips. I'll probably post it sometime around 5am ish.

  13. #10
    Julie's Avatar
    SMF Badges of Honor


    Member since
    Feb 2012
    Location
    Grass Valley California
    Posts
    420
    Thanks
    432
    Thanked 438 Times in 162 Posts
    Is this the thread that you told me that you were in the process of writing a while back? When I was talking to you about the boards that I was working with - you may not remember...

  14. #11
    Dunemaul started this thread.
    Dunemaul's Avatar
    SMF Badges of Honor



    Member since
    Nov 2011
    Location
    East Orlando FL
    Posts
    1,064
    Thanks
    157
    Thanked 560 Times in 301 Posts
    Yes it is Julie currently im half finished with the rest of the article and ill finish it when i get the chance. Just been to busy later.

  15. #12
    SMF Badges of Honor

    Member since
    May 2012
    Location
    central florida
    Posts
    139
    Thanks
    5
    Thanked 46 Times in 29 Posts
    I want to know where to find an Intel 4004.

  16. #13
    TheHoss's Avatar
    SMF Badges of Honor

    Member since
    Mar 2011
    Location
    The tater state
    Posts
    863
    Thanks
    1,112
    Thanked 840 Times in 279 Posts
    Jaydee i saw an IC chip on fleebay going for CRAZY $$$$. Like, $5000+. Was insane. I want to find THAT one!

  17. #14
    TheHoss's Avatar
    SMF Badges of Honor

    Member since
    Mar 2011
    Location
    The tater state
    Posts
    863
    Thanks
    1,112
    Thanked 840 Times in 279 Posts
    Good article, Dune. I don't know how the late future of E-Scrap is going to look. 10+ years from now, what will i be paying for computers? .50c? Who knows.

  18. #15
    Dunemaul started this thread.
    Dunemaul's Avatar
    SMF Badges of Honor



    Member since
    Nov 2011
    Location
    East Orlando FL
    Posts
    1,064
    Thanks
    157
    Thanked 560 Times in 301 Posts
    The article contains were to find that exact chip. I been looking for the item they are found in and still no luck.

  19. #16
    TheHoss's Avatar
    SMF Badges of Honor

    Member since
    Mar 2011
    Location
    The tater state
    Posts
    863
    Thanks
    1,112
    Thanked 840 Times in 279 Posts
    Fair enough. I know what i'll be reading tonight. Thank you.

  20. #17
    SMF Badges of Honor

    Member since
    May 2012
    Location
    central florida
    Posts
    139
    Thanks
    5
    Thanked 46 Times in 29 Posts
    Old calculators and test equipment are likely candidates Quote4004.com:
    To be fair, during the 1970-1971 period of Intel's 4004 development, Texas Instruments (TI) was also working on 4-bit CPU-on-a-chip technology for use in their line of calculator products. Regardless of who might have achieved "first silicon," there was a key difference between Intel's and TI's efforts. Although TI was developing a chip that contained all the elements of a microprocessor, it was designed to perform only one purpose, to be the "brain" of a calculator. Intel was also developing the 4004 for calculator applications, but their CPU-on-a-chip architecture could be programmed to control a wide variety of electronic devices from traffic signals to test equipment, according to the instructions stored in the external ROM. After the 4004's debut, Intel actively developed the nascent microprocessor market with their line of design tools like the Intellec 4, whereas TI focused on the "calculator on a chip" market for five years before finally releasing their TMS1000 family of 4-bit "microcontrollers" in 1976, which integrated the CPU, program ROM, data RAM, and I/O logic into a single chip. By then Intel had already introduced their famous 8-bit 8080, but there was plenty of market opportunities for TI's far less expensive, 4-bit "computer on a chip." Not long after, Intel introduced their own microcontroller family, the most famous being the 8-bit 8051, possible the most "cloned" microcontroller of all time and still in active use today.

  21. #18
    SMF Badges of Honor


    Member since
    Jan 2012
    Location
    Central Florida
    Posts
    629
    Thanks
    117
    Thanked 211 Times in 144 Posts
    ^You made it too easy


  22. Similar threads on the Scrap Metal Forum

    1. Another scrap article from my area
      By newattitude in forum General - Let's talk business
      Replies: 0
      Last Post: 08-23-2012, 11:45 PM
    2. Interesting recycling article
      By waredu in forum Misc. Metal Recycling
      Replies: 2
      Last Post: 08-13-2012, 03:43 AM
    3. Here is the article I wrote for my newspaper
      By Hypoman in forum General - Let's talk business
      Replies: 7
      Last Post: 06-03-2012, 10:46 AM
    4. good article I found
      By Dumpster-Dee in forum Tools and Equipment
      Replies: 2
      Last Post: 08-04-2011, 09:08 AM
    5. Useful Article
      By Theresa in forum Scrap Metal Tips and Advice
      Replies: 2
      Last Post: 04-25-2011, 11:31 PM

Thread Information

Users Browsing this Thread

There are currently 3 users browsing this thread. (0 members and 3 guests)

 
Browse the Most Recent Threads
On SMF In THIS CATEGORY.





OR

Bookmarks

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •  

The Scrap Metal Forum

    The Scrap Metal Forum is the #1 scrap metal recycling community in the world. Here we talk about the scrap metal business, making money, where we connect with other scrappers, scrap yards and more.

SMF on Facebook and Twitter

Twitter Facebook