Results 1 to 9 of 9

Battery Jump Packs

| General - Let's talk business
  1. #1
    ron22 started this thread.
    SMF Badges of Honor

    Member since
    Apr 2012
    Location
    Forest Lake, MN
    Posts
    248
    Thanks
    7
    Thanked 96 Times in 51 Posts

    Battery Jump Packs

    I received a call today about taking some Battery Jump Packs (The portable pack to jump start cars).
    They do factory warranty work. If they can get fixed they are, if not junk pile they go. All the batterys are removed.
    They have built in Air Compressor, USB port & Charger.
    They said they have pallets of them and get more all the time.
    What do you think
    Will I put in more hours tearing apart then it is worth?
    What to do with all the plastic?
    Also current pallets have all Battery leads cut off. They will leave them on in future if I will take them.



  2. #2
    Filthy's Avatar
    SMF Badges of Honor

    Member since
    Jul 2011
    Location
    Northern New Jersey
    Posts
    780
    Thanks
    850
    Thanked 372 Times in 202 Posts
    if they're free... ask them for the first pallet. process it, and decide for yourself. dont commit to all of them, but let them know if it works out you'd be prepared to take all of them, and even contract with them for removal and disposal.

    is it one of these?


    or a flat one like this?
    We're the renegades of Junk!

  3. #3
    ron22 started this thread.
    SMF Badges of Honor

    Member since
    Apr 2012
    Location
    Forest Lake, MN
    Posts
    248
    Thanks
    7
    Thanked 96 Times in 51 Posts
    I was told the brand but do not feel I should post it here.
    It is more like the second picture retails for $95.
    What would you scrap the Compressor as?
    I might see if I can get 1 and see what is inside.

  4. #4
    Filthy's Avatar
    SMF Badges of Honor

    Member since
    Jul 2011
    Location
    Northern New Jersey
    Posts
    780
    Thanks
    850
    Thanked 372 Times in 202 Posts
    Yeah. If you could get one.. that would be the best move. I would scrap the compressor as a sealed unit, or see if someone will buy them as cores.

  5. #5
    hobo finds's Avatar
    SMF Badges of Honor


    Member since
    Nov 2010
    Location
    tucson, az
    Posts
    4,758
    Thanks
    6,037
    Thanked 5,910 Times in 2,556 Posts
    I think each one will have small electric motor, small amount of brass on jumper ends, insulated wire, painted alum plate where air guage is and a few steel screws. Now if you could turn them all in as is for shread price (like a vacume cleaner) depending on the weight of one, that may be the way to go.

  6. #6
    Filthy's Avatar
    SMF Badges of Honor

    Member since
    Jul 2011
    Location
    Northern New Jersey
    Posts
    780
    Thanks
    850
    Thanked 372 Times in 202 Posts
    he said the battery leads (i think that means cables) are missing from the first batch. those are nice gauge. they would add significantly to the value, and if taking the first couple pallets means you have access to better product in the future, i think it would be worth a little effort to establish a relationship with the company.

    also let them know what else you'd be interested in, and even willing to pay for some types of scrap. they may not know what you're willing to work with

  7. The Following User Says Thank You to Filthy for This Post:


  8. #7
    happyscraper's Avatar
    SMF Badges of Honor


    Member since
    Feb 2012
    Location
    spring hill,fl
    Posts
    2,864
    Thanks
    350
    Thanked 1,371 Times in 847 Posts
    If I remember right the compressor or air pump is cast aluminum. I just put them in the dirty cast aluminum pile. Insulated wire inside, if they had the cables on them and you didn't have to drive to far it would be worth it. Like the above post try to get a few and take them apart and see what you think.

  9. #8
    ScrapperNJ26's Avatar
    SMF Badges of Honor


    Member since
    Jan 2011
    Location
    Clementon NJ
    Posts
    512
    Thanks
    537
    Thanked 148 Times in 89 Posts
    The batteries for these jump packs are almost 2/3rd's the price of the units...but if they are only $95 new they are like mid-grade as far as quality goes. Take out the compressors and batteries and stock pile them until you get them all done and or wait for the price to go up. If the batteries and leads are gone, don't buy them at all if they want to give them to you that's fine. There's no money there for just the compressors.





    Here is the one I have

    Jump Start Pack/Compressor | AW Direct

    New $275 Unit

    Replacement Batteries are $170

    The cables for the units you have may be 8,6 or 4 gauge.
    Last edited by ScrapperNJ26; 08-16-2012 at 04:54 PM.

  10. #9
    ron22 started this thread.
    SMF Badges of Honor

    Member since
    Apr 2012
    Location
    Forest Lake, MN
    Posts
    248
    Thanks
    7
    Thanked 96 Times in 51 Posts
    Ok went out and talked to the owner of the company. Got a different story from him. They get more than one model. Some are cheap with just battery and cables, some have the compressor and lights, some of the nicer larger ones too. They do not even try to fix them. They usually have bad batterys so not cost effective to fix.
    They did go through a phase of pulling cables and batterys from 1 or 2 pallets. They have more pallets with everything still on them.

    They showed me the ones that they had apart and there is a small charger(Basicly cell phone charger). Two small low grade PCB 1 is about 1.5" x 6" other is about .25" x 1" avery small electric motor bolted to a air pump. The pump is alum but very samll and would have to unbolt from motor. A few short sections of insulated wire.
    I told them the ones without batterys and cables are worthless and I would charge if that is all they gave me. (they currently can not get rid of them becuase of the PCB inside)

    The owner said it was not worth their time to do anything to them he would like to make a deal for the complete units. The problem is he said he gets $7 for the one size battery. It weights about 13# and at $0.28 so $3.64. His place deals in alot of batteries and they send them in by the truck load. So maybe he does get that much.
    Then there is the cables anywhere from 1 - 4 ft Maybe #8 or 6 insulated. Then some have the airpump and PCB and some dont.

    I need to get back to him tomorrow. I think I will say I will take them but not really wanting to pay anything for them. I have to transport them and deal with the disposal of the plastic.

    They did give me 2 units with batteries and cables so at least I paid for my gas to run out there


  11. Similar threads on the Scrap Metal Forum

    1. Finally making the jump into paid advertising
      By ScrapperNJ26 in forum General - Let's talk business
      Replies: 7
      Last Post: 07-15-2012, 03:21 PM
    2. eproms, flat packs, ic chips etc
      By EcoSafe in forum General Electronics Recycling
      Replies: 4
      Last Post: 06-16-2012, 02:23 PM
    3. Semi clutch packs/plates
      By Multimedia51 in forum Dismantling, Breaking Down & Maximizing Scrap
      Replies: 0
      Last Post: 05-18-2012, 06:33 PM
    4. Battery vs. Plugin
      By Rollyrogers33 in forum Tools and Equipment
      Replies: 11
      Last Post: 04-30-2012, 10:52 PM

Thread Information

Users Browsing this Thread

There are currently 2 users browsing this thread. (0 members and 2 guests)

 
Browse the Most Recent Threads
On SMF In THIS CATEGORY.





OR

Bookmarks

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •  

The Scrap Metal Forum

    The Scrap Metal Forum is the #1 scrap metal recycling community in the world. Here we talk about the scrap metal business, making money, where we connect with other scrappers, scrap yards and more.

SMF on Facebook and Twitter

Twitter Facebook