Page 1 of 2 12 LastLast
Results 1 to 20 of 30

A new refrigerant buyer for me.

| Off Topic Discussions
  1. #1
    freonjoe started this thread.
    SMF Badges of Honor


    Member since
    Nov 2011
    Location
    boise, ID
    Posts
    1,605
    Thanks
    469
    Thanked 1,462 Times in 668 Posts

    A new refrigerant buyer for me.

    As some of the older members of this forum are aware, I was using AirGas to sell my refrigerants. After having such horrible experiences with them, I finally found a new buyer. I decided to give Alfa Cantor out of Texas a try. I sent off a trial shipment of 500 pounds of R22 to see how it goes. I will keep this post updated just in case others are looking for a new buyer.

  2. The Following 11 Users say Thank You for This Post by freonjoe:



  3. #2
    SHOGOR's Avatar
    SMF Badges of Honor


    Member since
    Jul 2015
    Location
    NEW JERSEY
    Posts
    16
    Thanks
    5
    Thanked 27 Times in 9 Posts
    Did you have to rent their tanks? What are they paying for R22, whats their minimum and is the freight on them ?
    Will they dispose of mixed gas or free ? Let me know, thanks.

  4. #3
    freonjoe started this thread.
    SMF Badges of Honor


    Member since
    Nov 2011
    Location
    boise, ID
    Posts
    1,605
    Thanks
    469
    Thanked 1,462 Times in 668 Posts
    Hi SHOGOR, I don't know if they rent tanks, I already have a forest of them. They pay freight on shipments of 200 pounds or more. Their pay schedule goes pretty deep before they charge for disposal. IE, they pay down to 80% on R12 and R22.

  5. #4
    freonjoe started this thread.
    SMF Badges of Honor


    Member since
    Nov 2011
    Location
    boise, ID
    Posts
    1,605
    Thanks
    469
    Thanked 1,462 Times in 668 Posts
    So this is my first update. I shipped out refrigerants on 4/19 and they were received today (4/26). My exchange tanks are being delivered tomorrow. I shipped (4) 125# tanks with 110 pounds average R22 that tested out at 100% purity. I also shipped (1) 125# tank with 120 pounds of mixed R22 that tested out at 97.5% purity. My Nuetronics analyzer only does vapor tests so I'm curious how close it comes to their liquid tests. Let's see if they really can get a check out within 30 days of receiving the shipment.

  6. The Following 6 Users say Thank You for This Post by freonjoe:


  7. #5
    SMF Badges of Honor



    Member since
    Jul 2011
    Location
    Jacksonville, NC
    Posts
    4,917
    Thanks
    15,632
    Thanked 5,861 Times in 2,713 Posts
    Thanks for the update with the details. Mike
    "Profit begins when you buy NOT when you sell." {quote passed down to me from a wise man}

    Now go beat the copper out of something, Miked

  8. #6
    freonjoe started this thread.
    SMF Badges of Honor


    Member since
    Nov 2011
    Location
    boise, ID
    Posts
    1,605
    Thanks
    469
    Thanked 1,462 Times in 668 Posts
    Just an update. I got my receiving report back today. 1 tank tested at 99.77% purity with 100# net weight, 3 tanks tested at 99.5% purity with a net weight of 277#. The mixed tank was 91.08 purity and a net weight of 104# Overall, I am very happy with this company so far and will be sending them another shipment at the end of the month. They have been very good at communicating and the check is in the mail!

  9. The Following 4 Users say Thank You for This Post by freonjoe:


  10. #7
    SMF Badges of Honor



    Member since
    Jul 2011
    Location
    Jacksonville, NC
    Posts
    4,917
    Thanks
    15,632
    Thanked 5,861 Times in 2,713 Posts
    I am licensed but will not be involved in the refrigerant business due to my physical limits but am still interested in this business. I believe there are business opportunities awaiting members if they take the time to study your posts.



    I hope you don't mind explaining the importance in the difference in purity. When I look at your numbers there doesn't seem like a big difference between 99. 77% and 99.5% purity. Does the difference change the payout much?

    It seems to me that the purity you got was good, is this due to the testing you do before putting the refrigerant into your larger storage tanks? I recall you mentioned a tester in the past so which one do you use and how important is it to your business? 73 Mike

  11. #8
    freonjoe started this thread.
    SMF Badges of Honor


    Member since
    Nov 2011
    Location
    boise, ID
    Posts
    1,605
    Thanks
    469
    Thanked 1,462 Times in 668 Posts
    Hi Mike.
    Their payouts are based on purity.

    99.5 and above
    98 to 99.49
    90 to 97.99
    80 to 89.99

    It really does make a difference being able to test purity as there are large price differences. The top tier pays 7.00 a pound, the second tier pays 4.25 a pound and the third tier pays 3.00 a pound. A little mistake can be expensive! Oh, the fourth tier pays .75 a pound.

    P.S. I use a Nuetronics Ultima
    Last edited by freonjoe; 05-06-2016 at 07:11 PM.

  12. The Following 6 Users say Thank You for This Post by freonjoe:


  13. #9
    freonjoe started this thread.
    SMF Badges of Honor


    Member since
    Nov 2011
    Location
    boise, ID
    Posts
    1,605
    Thanks
    469
    Thanked 1,462 Times in 668 Posts
    An interesting update. I received my check today. That is well within the 30 days that they said they would do. Unfortunately, it is made out to my Email instead of me. I will be calling them tomorrow and see if they can get it straightened out.

  14. The Following 2 Users say Thank You for This Post by freonjoe:


  15. #10
    freonjoe started this thread.
    SMF Badges of Honor


    Member since
    Nov 2011
    Location
    boise, ID
    Posts
    1,605
    Thanks
    469
    Thanked 1,462 Times in 668 Posts
    A successful end to my first dealings with Alfa Cantor. My corrected check showed up today! So far, I have nothing but good things to say about this company. Hopefully, I will be sending off another shipment to them next week! I will keep this post updated when I ship again.

  16. The Following 4 Users say Thank You for This Post by freonjoe:


  17. #11
    eesakiwi's Avatar
    SMF Badges of Honor



    Member since
    Dec 2010
    Location
    NZ
    Posts
    2,531
    Thanks
    2,909
    Thanked 2,556 Times in 1,227 Posts
    How much money did you make and how many fridges/freezers/AC units did you reclaim the gas from?

    I'm really interested to find out. Thanks for the posts you have made to show us what potential is too.

  18. #12
    freonjoe started this thread.
    SMF Badges of Honor


    Member since
    Nov 2011
    Location
    boise, ID
    Posts
    1,605
    Thanks
    469
    Thanked 1,462 Times in 668 Posts
    Eesakiwi, This load all came from air conditioners as it was R22. The mixed refrigerant came from a customer, the rest came from air conditioners processed at the shop. It took about 250 air conditioners to get the 377 pounds of refrigerant. So the refrigerant is worth almost as much as the cleaned cu/al radiators. I take that back, it maybe more than the radiators as I get so much trash, I mean Trane. Like the old saying goes "the only way to stop a Trane is to turn it on!". If you get a calculator out and go up a few posts, you will know how much my check was.

  19. #13
    SMF Badges of Honor



    Member since
    Jul 2011
    Location
    Jacksonville, NC
    Posts
    4,917
    Thanks
    15,632
    Thanked 5,861 Times in 2,713 Posts
    Your contributions on this side of recycling have been amazing. Folks on the forum who are or perhaps should consider this a direction to go could not ask for a better mentor. Thank you.

    Also since the study guide is available getting a license is a snap.

    One area you may have addressed in the past but I am going to ask about now. What about the future of the refrigerant recovery with the newer refrigerants? Will reselling of the "new" refrigerants continue making it possible to make you money.


    I am under the understanding that the older refrigerants are more valuable in the recycling side because they are no longer being manufactured but still being used. If I am mistaken on this please correct me. Again thanks for sharing your knowledge. 73 Mike

  20. #14
    freonjoe started this thread.
    SMF Badges of Honor


    Member since
    Nov 2011
    Location
    boise, ID
    Posts
    1,605
    Thanks
    469
    Thanked 1,462 Times in 668 Posts
    Hi Mike.
    The use of R12 was discontinued in 1994, which is 22 years ago. 15% of the refrigerators that I get are still R12 and it sells for 18.00 a pound if it isn't mixed. Right now they are still manufacturing R22 in a limited amount and it brings 7.00 a pound if it isn't mixed. The newer refrigerants like R134a, R404a and 410a are all worth less than 1.00 unmixed. Right now the newest refrigerants like R290 and R600 have no value. I don't foresee the newer refrigerants going up in value any time soon. 410a is such a poor refrigerant that 20% of the air conditioners I get in are 410a and most of those have failed. Considering that they have only been out a few years, I don't think that bodes well for the industry. I think for the next 10 years R22 will only go up in value as the supply of virgin dwindles.

  21. The Following 3 Users say Thank You for This Post by freonjoe:


  22. #15
    DakotaRog's Avatar
    SMF Badges of Honor



    Member since
    Aug 2014
    Posts
    1,611
    Thanks
    602
    Thanked 1,675 Times in 830 Posts
    Cool thread!!

    [QUOTE]410a is such a poor refrigerant that 20% of the air conditioners I get in are 410a and most of those have failed. Considering that they have only been out a few years, I don't think that bodes well for the industry. [QUOTE]
    If the new stuff is that bad, I would expect the a/c manufacturers to put the heat (pardon my pun) on the politicians to make the EPA find something else to replace it. If the gov doesn't want the old "bad" stuff because of environmental concerns, make sure the new stuff is good!!

  23. #16
    DakotaRog's Avatar
    SMF Badges of Honor



    Member since
    Aug 2014
    Posts
    1,611
    Thanks
    602
    Thanked 1,675 Times in 830 Posts
    The top tier pays 7.00 a pound, the second tier pays 4.25 a pound and the third tier pays 3.00 a pound. A little mistake can be expensive! Oh, the fourth tier pays .75 a pound.
    Sounds like the current price scale of coon hides but not by the pound!

    So the refrigerant is worth almost as much as the cleaned cu/al radiators. I take that back, it maybe more than the radiators
    Sounds like castor removal from beavers considering the terrible low prices of most wild fur. Maybe not quite there yet that castor is worth more than the fur but coming close in some cases...

  24. #17
    nutpie's Avatar
    SMF Badges of Honor


    Member since
    Feb 2014
    Location
    maine
    Posts
    441
    Thanks
    379
    Thanked 404 Times in 227 Posts
    Quote Originally Posted by eesakiwi View Post
    How much money did you make and how many fridges/freezers/AC units did you reclaim the gas from?

    I'm really interested to find out. Thanks for the posts you have made to show us what potential is too.
    No less than $2100 USD.

  25. #18
    freonjoe started this thread.
    SMF Badges of Honor


    Member since
    Nov 2011
    Location
    boise, ID
    Posts
    1,605
    Thanks
    469
    Thanked 1,462 Times in 668 Posts
    I sent off my second shipment yesterday to Alfa Cantor. This shipment consisted of (3) 125# tanks of pure R-22, (2) 125# tanks of mixed R-22, (1) 125# tank of mixed R-12 and (1) 125# tank of R-410. In an earlier post I said that roughly 15% of the refrigerators that I get are R-12. I just started another new contract that is dropping of 20+ refrigerators a day and those are running about 75% R-12. I will keep the board updated on how well Alpa Cantor does on this shipment.

  26. The Following 8 Users say Thank You for This Post by freonjoe:


  27. #19
    DakotaRog's Avatar
    SMF Badges of Honor



    Member since
    Aug 2014
    Posts
    1,611
    Thanks
    602
    Thanked 1,675 Times in 830 Posts
    Sounds like those old frigs are the best. The next time I tip one back, I'll wish "more R-12 for freonjoe until he can't find any more!!!"
    Last edited by DakotaRog; 07-16-2016 at 04:50 PM.

  28. The Following User Says Thank You to DakotaRog for This Post:


  29. #20
    SMF Badges of Honor



    Member since
    Jul 2011
    Location
    Jacksonville, NC
    Posts
    4,917
    Thanks
    15,632
    Thanked 5,861 Times in 2,713 Posts
    Thanks for continuing to take the time to contribute on this subject. You know the ins and outs and show a realistic picture of this side of recycling. I hope some of our youger members are paying attention and learning. 73 Mike

  30. The Following User Says Thank You to miked for This Post:



  31. Similar threads on the Scrap Metal Forum

    1. MY Core Buyer is in need of a Buyer of Aluminum Rims- Central Indiana
      By sledge in forum General - Let's talk business
      Replies: 10
      Last Post: 11-22-2016, 06:58 PM
    2. Buyer & Seller threads updated with Buyer Last Active Time-Stamp
      By admin in forum Scrap Metal Forum News, Announcements, and Rules
      Replies: 2
      Last Post: 07-23-2014, 10:38 PM

Page 1 of 2 12 LastLast

Thread Information

Users Browsing this Thread

There are currently 2 users browsing this thread. (0 members and 2 guests)

 
Browse the Most Recent Threads
On SMF In THIS CATEGORY.





OR

Bookmarks

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •  

The Scrap Metal Forum

    The Scrap Metal Forum is the #1 scrap metal recycling community in the world. Here we talk about the scrap metal business, making money, where we connect with other scrappers, scrap yards and more.

SMF on Facebook and Twitter

Twitter Facebook