Thinking about mounting a winch to my trailer for general use any suggestions and reasoning for a min. Load rating?
Thinking about mounting a winch to my trailer for general use any suggestions and reasoning for a min. Load rating?
anything but hf badlands
Liberty Towing & Recycling
(732)279-8599
Cleaning up NJ 1 LB at a time!
Certified Mobile Scales
Fully Insured Carrier usdot # 1802487
WWW.LibertyTowing.Webs.Com
WWW.TRRecycles.Webs.com
Ok so I'm thinking that 2500 lb would be good for general use and pulling stuck items.
If you plan on winching up vehicles(I have no idea if you do or don't) then 2500 isn't going to cut it. I use a 10 000 lb Superwinch on my car trailer, and even with a snatch block it's really had to strain on some deeply stuck vehicles, especially old tractors that have been sitting in the same soft farmer's field for the last 30 years. So you may wish to consider a heavier winch. It's better to have it and not need it, than need it and not have it.
The winch on the car trailer is a Superwinch. I bought that brand because it was cheap, $300 for a 10k winch so I also bought a spare right away. But it's still a brand name that I trust to be somewhat reliable, unlike the stuff you get at Costco or Princess Auto. I stayed away from the better brands like Warn or Ramsey, even though they're more reliable IMO, because they're a bigger target/magnet for thieves. That's something I have to keep in mind, living in a big city with my trailers parked in a yard in an industrial area.
The winch I use on my dump trailer is an 8000lb Warn. It's not permanently mounted however, so it usually rides in the back seat of the truck until its needed. It's mounted on a steel plate mount that's welded onto the slide-in part of a receiver hitch. The receiver hitch itself is just an old hitch from a vehicle I scrapped, mounted on the front of the trailer and reinforced with some steel arms. Its awesome when you need it, like loading a big piece of scrap equipment from a place that has no forklift to load you. Its even come in really handy just securing down an awkward load with the cable. Each side of the trailer has tie-down eyelets mounted that are big enough to work the cable hook through, so I can zigzag it around if needed. You might want to consider keeping your winch removeable like that, if you don't expect to use it all the time. Keeps it out of the weather, and keeps it out of sight out of mind.
When you mount whatever winch you go with, have a secure snatchblock mount done right away too. It doubles your winch's power, and can come in super handy. Lastly, powering your winch. When I got the winch mounted on the car trailer, I mounted a battery and had the wiring done to keep it charged off the vehicle. That didn't work out well for me. Batteries wouldn't stay charged, and I killed a few before I gave up. I'm sure it's just a bad ground(s) somewhere, but hell if I can find where. Even the factory charging circuit on the dump trailer is a dud. And talking with other scrappers, its a common problem. So now I just run the winch on either trailer directly off a battery. I use a deep cycle group-31 sized battery (that's the battery size for big trucks). It lasts quite a while. For charging, I either take it home at night and throw it on a charger, or if I'm going to be somewhere a while, while loading or something, I'll just boost it off the truck. To connect the winch to the battery I use those large plastic 2-cable plugs like what are used to hook up the battery on an electric forklift, or you see the same plugs on the front of tow trucks to plug their booster cables into.
Hope this helps.
Last edited by zito; 01-26-2013 at 02:06 PM.
Hm. I have a small winch on my stake truck. For power I just hook jumper cables from the battery in my truck to the terminals on the winch. Is there any reason NOT to do that?
Burly Smash![/COLOR][/SIZE][/FONT]
John Terrell (248) 224-2188
Burly Guys Junk Removal LLC
5499 Perry Drive Unit P Waterford, MI 48329
http://www.burlyguys.com
That's a lot more load than your alternator is designed for. It's really hard on the alternator as well as being hard on the battery. This was explained to me by my battery guy (he's the guy I sell my scrap batteries to. He has a shop selling batteries, both automotive as well as doing a lot of off-grid stuff. He's also a licensed mechanic), and was confirmed by the owner of a small local shop that rebuilds starters, alternators, and motors. It's something that done enough, over time, will wear stuff out a lot quicker.
Don't get me wrong; it's something I've done myself before, and still do from time to time when I'm in a pinch, like say I've forgotten to charge a battery or forgotten the spare battery itself. But considering the winch is something I use a lot, I do whatever I can that minimizes (or even just -maybe- minimizes) the chances of something screwing up at a really inconvenient time.
Last edited by zito; 01-26-2013 at 03:09 PM.
The alternator is designed to put out X amount of amps
It will do this no matter what the load is on the Battery
If your total electrical load is greater then the Alternator puts out, then the current comes from the Battery
When the load reduces > Winch in off position, Battery recharges
Snow plows are now Electric over Hydraulic
Meaning there is a DC motor that operates the Hydraulic pump to position the plow
If doing small lots with a lot of re angling of the plow, sometimes you need to sit for a couple mins with the engine at high idle to recharge the Battery
LARGE Electrical load when plowing at night >> Heater blower on high, Heated seats on high, Mirrors defrost on, Light Bar going at full blast
For some reason Ford no longer puts a Voltage meter in the dash, so I have learned when the voltage drops the radio cuts out, time to idle for a couple mins
So when I pull a junk car onto the trailer,
I have a Battery in the trailer that operates the Hydraulics's and both winches
I have a Harbor Freight 12K for over 2 years and no problems and for the last 20 years have used the Ramsey 8K REP >> They seem to last 3 - 4 years between needing motors
The connection I use for the power to the trailer is a jump system
Lexan Plug Jump-Start Set with 500 Amp Clamps - Superior Signals | AW Direct
I have a plug setup in front and rear of the truck
Single Replacement Plug End - Superior Signals | AW Direct
I keep my trucks for about 7 years and they get between 230K and 250K on them before I sell them
This is my third Ford SD >> Had 95, 02 and the current 08 >> I have never had to replace an alternator
I do go thru Batteries about every 3 years >> I like the Sears Die Hard for the Warranty
Thanks JohnC, learn something new every day. As I say, that's how it was explained to me, and it seems to make sense to me. Even if it's just a placebo effect, it's how I'll keep doing it for peace of mind. I mean, even worst case scenario, I can't go wrong by carrying an extra battery around with me.
I have 2 HF badlands 12k. I've broke a few but with the 2 year warranty they just give you a new one. It is worth the money. I also have a group 31 battery on both of my trailers. Then I gave my plug wired up so it charges my battery as I'm driving down the road.
John and resourceful, if I'm understanding your set ups correctly, you're running your truck and trailer batteries in parallel. Should give you lots of juice for your winch or do you unplug the truck-trailer connection before running the winch? Battery banks for back-up power use this arrangement.
Yep, same with me.
Just one caution with this set up though - with the extra current available from the two batteries, you need to ensure you have overcurrent protection (fusing) for your winch so you don't smoke it under heavy load. Consult your owner's manual or contact the manufacturer.
There are currently 1 users browsing this thread. (0 members and 1 guests)
Bookmarks