Results 1 to 5 of 5

Lawnmower repair... maybe?

| Scrap Metal Tips and Advice
  1. #1
    armstrt8 started this thread.
    armstrt8's Avatar
    SMF Badges of Honor


    Member since
    Apr 2014
    Posts
    148
    Thanks
    56
    Thanked 142 Times in 61 Posts

    Lawnmower repair... maybe?

    Question!

    I went to pick up a load of metal from an area that I cannot afford to live in =P
    In the load was a "trash" lawnmower that appeared to be in near new condition. I asked about it and she said that they lost the gas cap for it last spring, and since it was old (OLD?!!?!) they just bought a new one. It has since then sat in their garage/shed, NO GAS CAP ON, and GAS IN IT, as well as some floating leaves in the gas tank part. If working this lawnmower would be twice as nice as ours....



    Anyone know what I might be in for it I wanted to fix it? If I could spend under $75 to make it run it would be well, well worth it.

    Its a Toro high wheel self propelled mulching mower.


  2. #2
    junkisus's Avatar
    SMF Badges of Honor


    Member since
    Jan 2012
    Location
    NC mtns
    Posts
    30
    Thanks
    90
    Thanked 39 Times in 15 Posts
    Throwaway world we live in, rinse the tank out real good put a new plug in and fresh gas, if it doesn't want to idle a carb kit should take care of that.

  3. #3
    SMF Badges of Honor



    Member since
    Dec 2013
    Location
    Nebraska
    Posts
    512
    Thanks
    521
    Thanked 812 Times in 311 Posts
    Yep, just turn it upside down and let everything drain out. You might wait overnight and refill it with gas so the carb isn't flooded from being upside down. I had a nice one given to me from an estate this week and I used engine starting fluid to get it to "pop" and it finally decided to run after a few fails. Now I'm running it with Seafoam fuel treatment to clean up the carb. Those mulching mowers .....not sure I like em....I like to see grass fly. Mine is a lime green Lawn Boy.

  4. #4
    Mechanic688's Avatar
    SMF Badges of Honor



    Member since
    Mar 2011
    Location
    Warsaw , Ind. In the heart of the lakes, and down the street from the hotel where Al Capone stayed.
    Posts
    9,568
    Thanks
    11,247
    Thanked 10,730 Times in 4,728 Posts
    Talked to a few repairmen and they talk about a lot of water in our gas nowadays. What we do is go down to the local marina and buy our mower gas there as there does not seem to be any alcohol and minimal water in it, runs better in our mowers. Take a quart clear jar and fill it 1/2 to 3/4 with gas and let it set to see how much water is in your gas, you'll be surprised.
    P & M Recycling - Specializing in E-Waste Recycling.
    If you enjoy your freedom, thank a vet.

  5. #5
    Immulmen's Avatar
    SMF Badges of Honor

    Member since
    Dec 2011
    Location
    Windham Maine
    Posts
    284
    Thanks
    13
    Thanked 272 Times in 117 Posts
    Quote Originally Posted by Mechanic688 View Post
    Talked to a few repairmen and they talk about a lot of water in our gas nowadays. What we do is go down to the local marina and buy our mower gas there as there does not seem to be any alcohol and minimal water in it, runs better in our mowers. Take a quart clear jar and fill it 1/2 to 3/4 with gas and let it set to see how much water is in your gas, you'll be surprised.
    If you have E10 gas the alcohol will attract water the separate from the gas. Until the alcohol absorbs enough water you will not see any in the gas. A lot of marinas [not in Maine] have real gas with no alcohol. In Maine , unless you buy airplane or racing fuel [both illegal to use on the road] it has to be E10.


  6. Similar threads on the Scrap Metal Forum

    1. Broken ridding lawnmower worth at a scrap yard?? (I'm not scrapper aficionado)
      By Esprit in forum Scrap Metal Questions and Answers
      Replies: 24
      Last Post: 05-22-2015, 12:23 AM
    2. How much copper and/or aluminum is in a lawnmower?
      By NWOdrudge in forum Scrap Metal Tips and Advice
      Replies: 29
      Last Post: 11-23-2014, 09:36 AM
    3. My clock repair guy
      By Tincankeith in forum A Day in the Life of a Scrapper
      Replies: 2
      Last Post: 02-24-2014, 07:22 PM
    4. How do you scrap a riding lawnmower?
      By lastchance in forum Scrap Metal Tips and Advice
      Replies: 12
      Last Post: 03-30-2012, 04:40 PM

Thread Information

Users Browsing this Thread

There are currently 1 users browsing this thread. (0 members and 1 guests)

 
Browse the Most Recent Threads
On SMF In THIS CATEGORY.





OR

Bookmarks

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •  

The Scrap Metal Forum

    The Scrap Metal Forum is the #1 scrap metal recycling community in the world. Here we talk about the scrap metal business, making money, where we connect with other scrappers, scrap yards and more.

SMF on Facebook and Twitter

Twitter Facebook