copper coated wire (various types),loose & in motors & yard questions

This has been covered in previous posts, which I read through. Just want to confirm what I believe I understand and maybe add a few questions.

Copper coated: copper coating on outside
aluminum wire
tin, steel and other,
magnetic copper covered wires all go into #2 copper bucket



Enamel coated copper: copper under coating (cannot see)
blue, green, red colored wires also go in #2 copper bucket
Yard termed this 'enamel coated'

Have I understood what I've read at SMF correctly??

Question~
Electric motors with enamel coated wire (unstripped) too small to strip. such as blue wire.
Are these still ok as electric motors, or does the enamel wire cause a downgrade?

Question:
Yard says coated copper wire is NOT #2 coppper
How can I persuade them differently??? (reading at SMF, I believe they're wrong)

My fear:
If I mix the coated wires in #2 bucket (as I believe is correct to do), yard could downgrade entire bucket
If keep separate and bring to their attn., could also downgrade because they say 'enamel' is worth less
It seems being unsure/hesitant opens the opportunity for them to downgrade just cause the question is posed to them!
Leaning twd mixing.

Question:
#1 copper piping (only have a short pipe) pays different than copper wire?
Have some #1 sink faucet pipes and some wire thicker than pencil lead. But not a lg. volume.
Yes, it is separated from the other copper grade.


If you've made it this far, thanks for your patience! I am probably ovrthinking this, but I am nervous!! Like everyone at SMF a lot of work has gone into stripping, accumulating, etc. and I need to make the very most of what I have as a small-time recycler/scrapper. Using a car & garage as my workspace, but very thankful for this opportunity of getting paid for scrap metals is available!

May edit this post if I think of more related questions, instead of starting a new post.

I'll answer based on yards in my area:

This has been covered in previous posts, which I read through. Just want to confirm what I believe I understand and maybe add a few questions.

Copper coated: copper coating on outside
aluminum wire
tin, steel and other,
magnetic copper covered wires all go into #2 copper bucket NO!!!!!

Enamel coated copper: copper under coating (cannot see)
blue, green, red colored wires also go in #2 copper bucket
Yard termed this 'enamel coated' YES

Have I understood what I've read at SMF correctly??

Question~
Electric motors with enamel coated wire (unstripped) too small to strip. such as blue wire.
Are these still ok as electric motors, or does the enamel wire cause a downgrade?

Need to ask your yard. shouldn't downgrade it Check with your yard. One of mine is now checking all motors for aluminum windings and will not buy these as motors, but as dirty aluminum

Question:
Yard says coated copper wire is NOT #2 coppper
How can I persuade them differently??? (reading at SMF, I believe they're wrong)

You can't

My fear:
If I mix the coated wires in #2 bucket (as I believe is correct to do), yard could downgrade entire bucket
If keep separate and bring to their attn., could also downgrade because they say 'enamel' is worth less
It seems being unsure/hesitant opens the opportunity for them to downgrade just cause the question is posed to them!
Leaning twd mixing.

Question:
#1 copper piping (only have a short pipe) pays different than copper wire?
Have some #1 sink faucet pipes and some wire thicker than pencil lead. But not a lg. volume.
Yes, it is separated from the other copper grade.

Depends on yard


If you've made it this far, thanks for your patience! I am probably ovrthinking this, but I am nervous!! Like everyone at SMF a lot of work has gone into stripping, accumulating, etc. and I need to make the very most of what I have as a small-time recycler/scrapper. Using a car & garage as my workspace, but very thankful for this opportunity of getting paid for scrap metals is available!

May edit this post if I think of more related questions, instead of starting a new post.

Full article at Scrap Metal Forum: http://www.scrapmetalforum.com/scrap...#ixzz35ssbpCag

Thanks, Mthomasdev for replying! Everytime I think I have something figured out, I end up with more questions!!

So, the very magnetic copper coated wire (can see the copper coat clearly) but underlying metal is very magnetic …. what bucket - shred, correct?
What about aluminum coppper coated wire, believe I read #2 bucket? Wire that's copper coated and only very slightly magnetic in #2 also, right??

Will add the enamel coated copper wire to the #2 copper bucket. Thx

The electric motors I'll leave together for now and see what the yard says.
Just nervous about "surprises" and if I'll be able to think quickly enough to maximize money on the spot at the yard, if they try to downgrade.

The reason I asked about convincing the yard is because I read here on SMF about talking with them about why a metal should be in a certain catagory. Basically being ready to explain/justify the reasoning for why metals should be allowed in a certain bucket. Just trying to increase chances of metals being paid on correctly. But it is always the yard that has the final say, I understand that. Thx again~

Smashing yokes is a lot of fun. Make it easy on yourself an put it on a blanket/towel/something before you smash tho. Makes the clean up so much easier. An the Ferrite goes with shred, lest at my yard.

Like Red above...disregard if your not talking yokes, or don't do tvs. lol.

Sirscrapalot - "People are more violently opposed to fur than leather because it's safer to harass rich women than motorcycle gangs." - Unknown..but funny.

that to. I use a box with a sheet. Old sheets, an blankets. I get them all the time for free from yard sales an such as part of taking everything.

My box is just a wood box I picked up somewhere. nothing special. Put a sheet, smash with a hammer, or something heavy, yank out copper, run magnet when done with the box, pull out what I can/want, pull out any insulated wire, etc dispose of leftover plastic and glue.

Either way it makes for some good fun for me!

Sirscrapalot - smashy mcsmasher