Page 2 of 3 FirstFirst 123 LastLast
Results 21 to 40 of 56

Draining Gas from Cars - Page 2

| Scrap Metal Tips and Advice
  1. #21
    Yunkman started this thread.
    SMF Badges of Honor



    Member since
    Dec 2013
    Location
    Nebraska
    Posts
    512
    Thanks
    521
    Thanked 812 Times in 311 Posts
    Okay I confess....I DID use the skidsteer; not the shovel.


  2. The Following 5 Users say Thank You for This Post by Yunkman:



  3. #22
    SuperDave's Avatar
    SMF Badges of Honor


    Member since
    May 2012
    Location
    Usa
    Posts
    448
    Thanks
    526
    Thanked 278 Times in 170 Posts
    gas is likely to pour down the tank and get dirty before reaching the bucket. I like removing the tank by sticking a flat head screwdriver under the gas tank straps then cutting the straps with a grinder. Use the sawzall to cut the rubber lines then like mech said use the 12v pump inside the tank and if possible cut the fuel delivery line in front of the gas filter and connect your battery charger to the wires coming out of the gastank and voila filtered gas

    after doing a few you will be familiar with wire colors associated with car brands, usually its the 2 bigger wires or the pink one
    Last edited by SuperDave; 08-28-2014 at 07:30 PM.

  4. The Following 4 Users say Thank You for This Post by SuperDave:


  5. #23
    Yunkman started this thread.
    SMF Badges of Honor



    Member since
    Dec 2013
    Location
    Nebraska
    Posts
    512
    Thanks
    521
    Thanked 812 Times in 311 Posts
    Quote Originally Posted by SuperDave View Post
    gas is likely to pour down the tank and get dirty before reaching the bucket. I like removing the tank by sticking a flat head screwdriver under the gas tank straps then cutting the straps with a grinder. Use the sawzall to cut the rubber lines then like mech said use the 12v pump inside the tank and if possible cut the fuel delivery line in front of the gas filter and connect your battery charger to the wires coming out of the gastank and voila filtered gas

    after doing a few you will be familiar with wire colors associated with car brands, usually its the 2 bigger wires or the pink one
    I always put the gas into another container through a filtered (small screen) funnel. It will even keep the water back. Being on the farm, I thought it was universal to do so. I hate to make sparks around a gas tank but if it's not leaking, I can see where that would work. I've torched the straps before so there should be no difference.

  6. The Following 4 Users say Thank You for This Post by Yunkman:


  7. #24
    SMF Badges of Honor




    Member since
    Mar 2012
    Location
    ks
    Posts
    2,187
    Thanks
    2,513
    Thanked 2,140 Times in 898 Posts
    I thought I had a thread on this topic, maybe I just thought about writing one, who knows.
    Alvord iron and salvage
    3rd generation scrapper and dam proud of it

  8. The Following 3 Users say Thank You for This Post by taterjuice:


  9. #25
    SMF Badges of Honor



    Member since
    Jan 2011
    Posts
    1,159
    Thanks
    0
    Thanked 248 Times in 169 Posts
    yeah that way looks like a death trap.i am about to start trying to drain the gas out soon.I am going to try the return line up by the engine.It shouldnt be too hard to find

  10. #26
    SuperDave's Avatar
    SMF Badges of Honor


    Member since
    May 2012
    Location
    Usa
    Posts
    448
    Thanks
    526
    Thanked 278 Times in 170 Posts
    Should mention that my yard also wants a hole in the tank or for it to be removed. Just the method to my madness.

  11. #27
    JohnC4X4's Avatar
    SMF Badges of Honor


    Member since
    Apr 2011
    Location
    South East Ma
    Posts
    986
    Thanks
    162
    Thanked 1,127 Times in 514 Posts
    Quote Originally Posted by SuperDave View Post
    Should mention that my yard also wants a hole in the tank or for it to be removed. Just the method to my madness.
    If I had to do that then of course I would drain the gas
    BUT
    My yard takes them with the tanks still attached
    So no reason to drain them
    When Gas gets above $4.00 a gallon I may change my mind

    Right now when I purchase gas it is a deduction on the taxes
    If I start using drained gas >> That would reduce my deduction and make a smaller refund check >> Not to mention more work on my part

  12. #28
    Yunkman started this thread.
    SMF Badges of Honor



    Member since
    Dec 2013
    Location
    Nebraska
    Posts
    512
    Thanks
    521
    Thanked 812 Times in 311 Posts
    Quote Originally Posted by JohnC4X4 View Post
    Right now when I purchase gas it is a deduction on the taxes
    If I start using drained gas >> That would reduce my deduction and make a smaller refund check >> Not to mention more work on my part
    Use the gas in your lawnmower where it isn't deductible or sell it to your neighbor for $2.50 a gallon ....he'd be happy to get it.
    At .06 cents a pound, the gas left in a vehicle would bring you 36 cents per gallon. (Gas weighs 6 lbs per gallon) Just food for thought.

  13. The Following User Says Thank You to Yunkman for This Post:


  14. #29
    Patriot76's Avatar
    SMF Badges of Honor


    Member since
    Dec 2012
    Location
    Buffalo Commons
    Posts
    2,949
    Thanks
    10,591
    Thanked 7,218 Times in 2,256 Posts
    FYI - there is a story of a vehicle going through a shredder in a scrap yard. In the trunk was a propane tank, gas cans, and the gas tank was full. It exploded and destroyed a multi-million dollar shredder and half of the storage facility at the yard. Do you want to know why they ask for the title and VIN # of vehicles that are scrapped? They traced this vehicle back to the scrapper and filed a law suit for recovery of the damages. They went back through records from yard to yard until they found the individual. Lesson - Even if a yard accepts the metal, if it is a hazard you could be held responsible.

    To add to my previous post, gas tanks are emptied by shooting them with the caliber of your choice. After three months to six months a saw zaw or torch is used to cut the bans and remove the tank from the vehicle. The tank goes as unprepared (higher price than vehicles here) and the rest is sold separately. A picture of the vehicle with the trunk open is taken to make sure there is no doubt. This is a paranoid strategy, but for piece of mind it is worth it to me. The other strategy used is to flip the vehicle over and flatten the roof. This allows the loading of more vehicles on the trailer.

  15. The Following 2 Users say Thank You for This Post by Patriot76:


  16. #30
    Yunkman started this thread.
    SMF Badges of Honor



    Member since
    Dec 2013
    Location
    Nebraska
    Posts
    512
    Thanks
    521
    Thanked 812 Times in 311 Posts
    My particular yard crushes each vehicle and then piles three previously crushed vehicles together and the three go back into the crusher as one unit to flatten them some more. I'll have to take note of how many they get on a semi truck.

  17. The Following User Says Thank You to Yunkman for This Post:


  18. #31
    Scrappah's Avatar
    SMF Badges of Honor



    Member since
    Jun 2014
    Posts
    1,058
    Thanks
    320
    Thanked 1,419 Times in 676 Posts
    There have been some changes in the gasoline over the years. Most of it is blended with Ethanol. In some states it's the law that they have to tell you it's blended. In other states they don't tell you if it's not required. As far as i know the fuel in Canada is blended as well.

    I was talking with one of the sales reps from one of the larger oil companies a few years age. He said that it's only guaranteed to have a shelf life of 30 days from the time it was pumped at the gas station. Anytime after that it can begin what's called phase separation. It starts to break down into a low octane gasoline and high octane ethanol.

    There's a testing kit on the market that measures how far gone the fuel is.

    Looong story short .... I wouldn't recommend using the fuel out of a junker. If you dumped in a batch of stuff that had gone by it would be a major hassle. Maybe a day's work to drop your fuel tank and completely flush your fuel lines ? Maybe more if you ran into problems ?

  19. The Following 2 Users say Thank You for This Post by Scrappah:


  20. #32
    Scrappah's Avatar
    SMF Badges of Honor



    Member since
    Jun 2014
    Posts
    1,058
    Thanks
    320
    Thanked 1,419 Times in 676 Posts
    Quote Originally Posted by Patriot76 View Post

    To add to my previous post, gas tanks are emptied by shooting them with the caliber of your choice. .
    I was thinking incendiary rounds.

  21. The Following 2 Users say Thank You for This Post by Scrappah:


  22. #33
    Immulmen's Avatar
    SMF Badges of Honor

    Member since
    Dec 2011
    Location
    Windham Maine
    Posts
    284
    Thanks
    13
    Thanked 272 Times in 117 Posts
    Quote Originally Posted by Scrappah View Post
    There have been some changes in the gasoline over the years. Most of it is blended with Ethanol. In some states it's the law that they have to tell you it's blended. In other states they don't tell you if it's not required. As far as i know the fuel in Canada is blended as well.

    I was talking with one of the sales reps from one of the larger oil companies a few years age. He said that it's only guaranteed to have a shelf life of 30 days from the time it was pumped at the gas station. Anytime after that it can begin what's called phase separation. It starts to break down into a low octane gasoline and high octane ethanol.

    There's a testing kit on the market that measures how far gone the fuel is.

    Looong story short .... I wouldn't recommend using the fuel out of a junker. If you dumped in a batch of stuff that had gone by it would be a major hassle. Maybe a day's work to drop your fuel tank and completely flush your fuel lines ? Maybe more if you ran into problems ?
    The phase separation happens when the Ethanol absorbs too much water. Then like you said you have low octane gas and Ethanol mixed with water. I had about 7 gal that this happened to. My sidecar motorcycle has a flathead engine with 6.5 to 1 compression ratio. Due to the low compression it will run fine on fuel lower then 87 octane. I used the bad gas by adding it one gallon to about 4 fresh gas at a time. The only issue is this makes the engine run slightly richer.

  23. The Following 2 Users say Thank You for This Post by Immulmen:


  24. #34
    SMF Badges of Honor



    Member since
    Jan 2011
    Posts
    1,159
    Thanks
    0
    Thanked 248 Times in 169 Posts
    I want to start doing this because the cars i get have only been sitting a max of 6 months but it is most of the time alot less than that.
    Then i would have free gas for something lol

  25. #35
    Scrappah's Avatar
    SMF Badges of Honor



    Member since
    Jun 2014
    Posts
    1,058
    Thanks
    320
    Thanked 1,419 Times in 676 Posts
    < sigh > I feel like i'm getting too old sometimes. I've been watching the history of this blended fuel thing since the 1970's. Back then i was working for Gibbs oil company down in Massachusetts. After unleaded came on the market Gasahol debuted as the next great thing. The Granolas loved the idea of it. In practice ......... it turned out to be a really bad idea. I remember one cold day where route 1 down in Saugus was littered with broken down cars that had just filled up with the stuff at one of our stations.

    Anyway ... we sold the stuff for a couple of years and then it kind of quietly went away.

    The only reason we're stuck using it today is because of the Federal EPA. In the old days they used to use a lead compound in the gasoline as an anti knock additive. Lead is bad so the EPA mandated a changeover to an unleaded gas that used MTBE as an anti knock additive.

    You probably remember the big bruhaha here in Maine about MTBE leaching into our underground water supplies and poisoning them awhile back ?

    MTBE turned out to be bad so the EPA mandated that smaller amounts of ethanol should be added as an anti knock additive instead.

    From there they just ran with it. They've instituted a program where larger and larger amounts of Ethanol have to be blended in with the nation's gasoline supply as time goes on. If the trend continues we will be looking at gasoline with 100 octane or more at the pump. If your vehicle isn't designed for flex fuel you're S.O.L. You won't be able to buy fuel than can run your older car,truck,or small engine.

    ~ That's kinda the backstory ~

    The main reason i brought it up is because they have had to spend billions and billions to make changes that will allow the use of these new blended fuels.

    You're right about Ethanol and water problems. Ethanol will absorb water vapor from the air.

    The thing is that one of the changes that they've made is that fuel systems are closed systems now. The blended fuel isn't exposed to the open air.

    There's got to be something else going on .............

    You know how if you mix vinegar and oil it makes salad dressing ? I think it's kinda the same with this blended fuel. It will stay together for awhile but if you let it sit it will separate into it's two component parts. It makes sense that the low octane gasoline would drop to the lowest part of the tank where the fuel pump pickup is. If you can get the car started at all it will run like crap. If you happen to pick up a charge of that high octane (100+) Ethanol it will damage the combustion chamber.

    I've lost two chain saws this way. Bad gas just tore up the piston & cylinder walls.

    Loooong story short: The stuff that's available at the pump nowadays isn't very trustworthy. It's okay for your daily driver as long as you fill up with fresh fuel every week or two. Otherwise .... you wanna be careful.

    What's the most expedient thing to do with gas that you don't trust ?

    Most folks won't mess around with it. They'll just dump it out back in the woods somewhere.

    ( I put mine in a coffee can up on a cement block and light it up. It takes about an hour for all of the fuel to burn off.)

  26. The Following User Says Thank You to Scrappah for This Post:


  27. #36
    Yunkman started this thread.
    SMF Badges of Honor



    Member since
    Dec 2013
    Location
    Nebraska
    Posts
    512
    Thanks
    521
    Thanked 812 Times in 311 Posts
    Quote Originally Posted by Scrappah View Post
    ( I put mine in a coffee can up on a cement block and light it up. It takes about an hour for all of the fuel to burn off.)
    I sense that you're brighter than the average bear, Scrappah, but now we're back to "How to burn gasoline in a can without blowing yourself up"?

  28. The Following User Says Thank You to Yunkman for This Post:


  29. #37
    SMF Badges of Honor


    Member since
    Nov 2010
    Location
    Boise, ID
    Posts
    2,702
    Thanks
    2,237
    Thanked 2,352 Times in 1,014 Posts
    Quote Originally Posted by Yunkman View Post
    I sense that you're brighter than the average bear, Scrappah, but now we're back to "How to burn gasoline in a can without blowing yourself up"?
    Put fuel in can. Toss match into can. Burns like a candle. Just don't kick it over.

  30. The Following 2 Users say Thank You for This Post by IdahoScrapper:


  31. #38
    SMF Badges of Honor


    Member since
    Nov 2010
    Location
    Boise, ID
    Posts
    2,702
    Thanks
    2,237
    Thanked 2,352 Times in 1,014 Posts
    As for draining, my yard doesn't require it. But on vehicles that had usable fuel, I'd roll the vehicle on its side, then punch a hole with a cordless drill. Have yet to have an issue with sparks. Could use an air drill too.

  32. #39
    SMF Badges of Honor



    Member since
    Jan 2011
    Posts
    1,159
    Thanks
    0
    Thanked 248 Times in 169 Posts
    So after doing some research i found this.What do you think.Seems a little time consuming but seems to work good.But it is way over priced at 149.00 plus 6.95 for shipping.

  33. The Following User Says Thank You to Focker for This Post:


  34. #40
    Scrappah's Avatar
    SMF Badges of Honor



    Member since
    Jun 2014
    Posts
    1,058
    Thanks
    320
    Thanked 1,419 Times in 676 Posts
    Quote Originally Posted by IdahoScrapper View Post
    Put fuel in can. Toss match into can. Burns like a candle. Just don't kick it over.
    That's about the long and the short of it. I use one of those hand held, self igniting, propane torches. I just stand back, hold the tip of the torch to the rim of the can and then click the little button that starts the torch. There's a little POOF and then it starts a lazy burn.

    ~ Still makes my cheeks clench a little every time i do it ~

  35. The Following User Says Thank You to Scrappah for This Post:



  36. Similar threads on the Scrap Metal Forum

    1. Is it a good idea to reuse gas from junk cars?
      By Ptscrapper in forum Scrap Metal Questions and Answers
      Replies: 30
      Last Post: 03-09-2022, 11:56 PM
    2. Do you use the gas from your scrapped cars?
      By BurlyGuys in forum Dismantling, Breaking Down & Maximizing Scrap
      Replies: 24
      Last Post: 05-10-2021, 02:09 PM
    3. Gas Grills
      By 708bigbuck in forum Scrap Metal Tips and Advice
      Replies: 22
      Last Post: 11-23-2014, 12:28 PM
    4. Oil/gas draining
      By DevinThaScrapper in forum Scrap Metal Tips and Advice
      Replies: 14
      Last Post: 07-27-2013, 04:09 AM
    5. Gas furnace
      By Perrysplace in forum Scrap Metal Tips and Advice
      Replies: 6
      Last Post: 11-18-2012, 06:12 PM

Page 2 of 3 FirstFirst 123 LastLast

Thread Information

Users Browsing this Thread

There are currently 1 users browsing this thread. (0 members and 1 guests)

 
Browse the Most Recent Threads
On SMF In THIS CATEGORY.





OR

Bookmarks

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •  

The Scrap Metal Forum

    The Scrap Metal Forum is the #1 scrap metal recycling community in the world. Here we talk about the scrap metal business, making money, where we connect with other scrappers, scrap yards and more.

SMF on Facebook and Twitter

Twitter Facebook