"Wow this bag of phone chargers is heavy" - Page 3

Originally Posted by Dumpster Dee

Does this mean you won't keep sharing nicknames for your family jewelry that you almost melted!!!!!?????

bwwwhahaha!



Oh man, Hoss is never going to live this down. Ever.

Mind.


Blown.

Dee, i'll still call ya buddy.

And about the jewelry.....well i was raised to be a country gentleman, and can honestly say have never talked to a lady about my nether regions gettin shocked back to the 50's. But hell, theirs a first for everything!

Ah man, yall are somethin else i tell ya what.

Originally Posted by Dumpster Dee

Hoss, don't stop calling me buddy, now. I thought it was just a way of saying I was "like" one of the guys...not actually one of the guys. You do know that newattitude is a female also don't you. And we are the only two females who have posted consistently since I've been here. Does this mean you won't keep sharing nicknames for your family jewelry that you almost melted!!!!!?????

I seen you eyein my crotch when we met up....LOLOL just kiddin bud hahahaha.

Originally Posted by IdahoScrapper

bwwwhahaha!

Oh man, Hoss is never going to live this down. Ever.

Originally Posted by little726

I'm new here and have looked through the forum for the answer to a question I have. I just can't find an answer. Here goes: I tore apart a phone charger and found 2 windings with wire on them. One is shiny cooper wire, the other is bright red wire.

Is the bright red wire copper?

I've seen so many shades of red its not even funny! Also shades of green and yellow. Most times the yellow will be aluminum but you get the occasional 'yellow' coated copper. Oh, welcome!

^^^ I have seen some burned motors but didn't notice the bluish/green color, I will make sure to look closer next time. Lol, its funny when you come upon something that burned out if you can't smell it before tearing down and say to yourself, ''Yeppers, that burned out right there!''

on the big ones I always use my sawsall....sometimes cut down the center all the way to the "brick"...and sometimes turn it sideways and cut the whole side off (cut copper off right down side of "brick")and punch it through. It just takes a little practice like everything else and soon you'll be real fast at it. I know some like the grinder best....whatever works. Personally, I only use my grinder when I have to.....that thing is dangerous !! Wish I were more technalogically (sp?) oriented so I could make a video. Mech ???? Snodly???? Injun????

I have done a lot of those small transformers. Mostly 25 - 50 gms but theres bigger ones too.

I always look at them as 'the last Kg of copper' ie; "I would have had 5 & 1/2kg copper, but with them its 6Kg" (insert Lbs if you want to) So I actually got 1 Kg extra.

Easy ways>
Check if theres a weld down the sides of the iron core (like the microwave transformers) You can bash these ones with a hammer & the iron core breaks into 2 peices. Now rip the copper out.

Wood chisel or 'meat cleaver & hammer' one side of the copper windings off, punch the other side out, clean off insulation.

Cut thru one side of the windings with a cut off disc or a meat cleaver or chisel, chuck the thing in a fire & burn the insulation off.
Now rip out the loose copper windings (burnt copper!)

Cut directly thru the iron core with a meat cleaver inline with the laminations, sort the metals out.
(the last resort unless the design makes it easyer)

Pulling the laminations.
Depending on the design it can be easy once a few I & E's are removed, normally they are covered with varnish which glues them all together.

Burning the lot.
Burn them all off in a fire, use a longish tapered sharp knife down the gap between the copper coil & the core & hammer it down thru the gap while it cuts thru the 'now soft' copper wire. Easy & dirty.

Originally Posted by Scrap man

Yes, it's just painted. Someone mentioned somewhere on here that the makers of the windings will have them painted so the workers know what windings go where and don't mix them up.

Hi there, new here, just introduced myself a minute ago! -the windings are coated with a thin resin to provide insulation between each wire, the transformers work by either stepping up voltage and decreasing current or stepping down voltage and increasing current. This is done by the number of coils on opposite sides of the transformer which is why you will see one side has bigger coils but less of them and the other has smaller coils but more of them. If there was no insulation between the wires then both sides would basically count as 1 big wire on each side and so the transformer won't do it's job.

Even if it looks pure and not an off red orange colour it is still coated and this is why yards pay less for it. This applies to all wires in transformers, electromagnets and motors.

Originally Posted by tinman#30

Ok so i broke the black box apart after reading this earlier. But for the life of me i couldnt figure out a way that is time efficient to take the windings out. I tried breaking the metal retainers around it, to no triumph. Do they pay good for just the transformers and if not? Do you have any suggestions to get the windings out?

You could always take a hatchet to it. lol That being said, I've taken a tote full of nothing put plugs and those transformers and I remember getting a pretty good price for them. I think I even got more than insulated wire price for them.

Hit the small ones with a sledge. Works for me.

I've scrapped several arc welders and I cut the transformer in half with the chop saw

Good too see people are still SEARCHING and finding some good info on here.

By the way, for them little transformers out of the plug "boxes", i just use an angle grinder to get through it. Done it a million times. Put it in a bench clamp first though. Aint worth grindin down to yer knuckle.

hi
i have a bag of phone & telephone chargers would it really be feasible to cut them open or just cut wire off and scrap as they are