Advice for small timers

Hi all, I’m new here and just posted in the intro forum. As stated, I used to scrap a lot but due to a spine condition I’m pretty much slow with limited use of my left hand. I do save cans and strip copper sometimes, I was wondering if anyone had advice for someone in this situation? I am mechanical and can use small tools. Each day is different so some days are awful, some days I can get around in short spurts well. Anyway, I’m not on Dr Oz and we talking metal. Sorry for the story. I’d be much thankful for any input. Much gratitude, mark

Being confined to an apartment, where people in the complex throw away decent to awesome stuff all the time, ive stepped up my ebay game over the last year. It doesent compensate for being able to store large amounts of scrap but it helps.

Originally Posted by andyheim

Being confined to an apartment, where people in the complex throw away decent to awesome stuff all the time, ive stepped up my ebay game over the last year. It doesent compensate for being able to store large amounts of scrap but it helps.

If your apartment complex has a laundromat, you should advertise inside on the board for electronics pickup or any other scrap they may have.

Originally Posted by jimicrk

If your apartment complex has a laundromat, you should advertise inside on the board for electronics pickup or any other scrap they may have.

Also put a sign by the dumpster area!

Thank you all so much. I get electronics and such given to me at times. I need to get into the threads for small stuff and figure out what I’m looking for and any safety issues. As I said, I’m mainly a can saver.

The only advice i have would be to use whatever tools you can to make things easier. Get a small vise to hold items as you take them apart. Use cordless grinder, impact, etc. Pick up some cheap 4 wheel moving dollies from Harbor Freight to make it easier to move scrap in and out. Good luck. let me know if you have any other questions.

Thank you. I’m just looking at one example as I’ve got an older DVD player that I picked up from a relative. Is it worth going into? I’m wondering about the power cords but I know they are thin and likely hard to strip but inside? I’m currently searching now but haven’t found anything. This may be a stupid question and in the wrong thread. Again, thanks.mb

not sure about the extent of your injury but theres a guy around here that got his arm paralyzed awhile back and had the doctors cut it off. so he's only got one arm now and still manages to lift engine blocks into his truck by himself. its all about will power. if you want to do something you can find a way to get it done. not saying you need to kill yourself but maybe build a small crane on your truck or trailer with an electric winch running the drag line if your unable to lift big stuff by hand.

Thanks again for taking time to answer. You folks have helped me a lot. I got the DVD player apart cleanly and got the boards, 1 green, 1 brown\green. I’ve got the cord but haven’t stripped it. I’m reading all I can and learning from the wealth of info. I hope I can find a buyer in SC or Charlotte NC. I didn’t see any listed. I’m looking at the list to see the minimum wts n such but I’m sure I’ll collect for quite a while. Scrapman, my problem is the spine. I have balance issues n such and lift a fraction of what I used to. It’s sad but true that I was a heavy drinker for many yrs and I’ve fallen and gotten injured many more times in the 7 yrs sober than 25 drunk. A funny irony of life on earth I guess.

If your disabled you would prolly qualify for one of those hyd cranes they put on the corner of the truck beds to load elect wheelchairs. Theres a guy over here that uses it to load larger items into his truck. Most scrayards will hel you unload. Just something you may want to check on.

It sounds like a sit down job would be the best fit if it's a struggle to get around on a bad day.

E-waste isn't too hard but it's an industry in decline. One of the biggest reasons is that consumers have gone from computer towers & laptops to tablets and pads. The tablets & pads are uncommonly difficult to repair and don't have very much scrap value. (I'm only shipping 1/3 of what i did a few years ago.)

Best advise for somebody just getting back into scrapping would be to get a digital weigh scale that goes up to 100 lbs. Weigh everything up as you go along. That way you can run the numbers and decide if a particular thing is working for you or not.

Were I in your shoes, I would set up with only taking (buying) clean boards and stripping them for IC/tant/plating this way you dont deal with mountains of plastic and sheet metal. Then either sell the sorted components by the pound or better yet refine the PM myself.

But to each their own.