Results 1 to 10 of 10

Semi starters & alternators

| Scrap Metal Tips and Advice
  1. #1
    Multimedia51 started this thread.
    SMF Badges of Honor

    Member since
    Apr 2012
    Location
    canada
    Posts
    6
    Thanks
    0
    Thanked 0 Times in 0 Posts

    Semi starters & alternators

    Hey new to the forum, been scrapping since August of 2011. Must say its a whole new world and I like it. I picked up 14 semi starters and 10 alternators the other day. I did this last year as well but had little to go on so just scrapped them. After the starters were taken apart it worked out to about $17.00 in scrap metal. What my question is.....
    Is there a better market for these then scrap or what is the best root to maximise profits. Any help would be appreciated.



  2. #2
    SMF Badges of Honor



    Member since
    Feb 2012
    Location
    OK
    Posts
    5,731
    Thanks
    6,815
    Thanked 3,465 Times in 1,990 Posts
    you might should go to the introduce yourself section (main SMF page, near the bottom) before the introduce yourself police get here ; ) I've seen posts that recommended checking parts place core return payments on some things, sure might be worth a try on those.

    (down here they don't allow semis to go around dropping stuff like that, but that's just here)
    Last edited by Bear; 04-16-2012 at 09:38 PM.

  3. #3
    SMF Badges of Honor

    Member since
    Mar 2012
    Location
    Chesaning
    Posts
    472
    Thanks
    24
    Thanked 355 Times in 171 Posts
    I sell them as cores. Get $23 each here.

  4. The Following User Says Thank You to ResourcefulRecycling for This Post:


  5. #4
    SMF Badges of Honor



    Member since
    Feb 2012
    Location
    OK
    Posts
    5,731
    Thanks
    6,815
    Thanked 3,465 Times in 1,990 Posts
    $23 don't seem like much for a semi? some of those things sell in the hundreds of dollars don't they ?

  6. #5
    Multimedia51 started this thread.
    SMF Badges of Honor

    Member since
    Apr 2012
    Location
    canada
    Posts
    6
    Thanks
    0
    Thanked 0 Times in 0 Posts
    My apologise on the introduction
    Quote Originally Posted by Bear View Post
    you might should go to the introduce yourself section (main SMF page, near the bottom) before the introduce yourself police get here ; ) I've seen posts that recommended checking parts place core return payments on some things, sure might be worth a try on those.

    (down here they don't allow semis to go around dropping stuff like that, but that's just here)

  7. #6
    Multimedia51 started this thread.
    SMF Badges of Honor

    Member since
    Apr 2012
    Location
    canada
    Posts
    6
    Thanks
    0
    Thanked 0 Times in 0 Posts
    Hey Bear, yeah I think $23 would be on the low side. Some of the ones I have are 4-800 new.

  8. #7
    SMF Badges of Honor

    Member since
    Jan 2012
    Location
    South Central Minnesota
    Posts
    232
    Thanks
    123
    Thanked 230 Times in 107 Posts
    Quote Originally Posted by Bear View Post
    $23 don't seem like much for a semi? some of those things sell in the hundreds of dollars don't they ?
    Value as a returnable core or to a core buyer in most cases has nothing to do with the purchase price of part. Its kind of like the supply-demand thing. In past years replacing auto parts sometimes the core charge was much higher than the cost of the part. Makes you get the replaced part back in short order.
    As a driver I'm always sober, but my truck is always ready to get loaded

  9. #8
    Multimedia51 started this thread.
    SMF Badges of Honor

    Member since
    Apr 2012
    Location
    canada
    Posts
    6
    Thanks
    0
    Thanked 0 Times in 0 Posts
    Ok so my best bet would be to locate a core buyer and start with that. Thanks for the help

  10. #9
    SMF Badges of Honor


    Member since
    Jan 2012
    Location
    Eastern Ontario
    Posts
    294
    Thanks
    139
    Thanked 242 Times in 119 Posts
    Just wondering out load here. If you could find out which ones are popular and used a lot, would it be worth taking them into a starter / alternator repair guy and having them fixed to resell.

  11. #10
    Multimedia51 started this thread.
    SMF Badges of Honor

    Member since
    Apr 2012
    Location
    canada
    Posts
    6
    Thanks
    0
    Thanked 0 Times in 0 Posts
    Quote Originally Posted by devo View Post
    Just wondering out load here. If you could find out which ones are popular and used a lot, would it be worth taking them into a starter / alternator repair guy and having them fixed to resell.
    Yeah that crossed my mind as well but I would rather sell them to the repair guy becuase I wouln't want some big angry trucker looking for me if it stopped working while they were on the road. When it comes to that kind of stuff I'd rather let the pro's deal with it. Thanks for the reply.


  12. Similar threads on the Scrap Metal Forum

    1. UK Scrap Values starters and alternators
      By scrapcar in forum Scrap Metal Prices
      Replies: 0
      Last Post: 06-30-2012, 10:38 AM
    2. The small silver ceramic discs in fridge compressor starters & the odd CRT Tv
      By eesakiwi in forum General Electronics Recycling
      Replies: 4
      Last Post: 04-15-2012, 11:55 PM

Thread Information

Users Browsing this Thread

There are currently 2 users browsing this thread. (0 members and 2 guests)

 
Browse the Most Recent Threads
On SMF In THIS CATEGORY.





OR

Bookmarks

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •  

The Scrap Metal Forum

    The Scrap Metal Forum is the #1 scrap metal recycling community in the world. Here we talk about the scrap metal business, making money, where we connect with other scrappers, scrap yards and more.

SMF on Facebook and Twitter

Twitter Facebook