Results 1 to 5 of 5

Vintage Motherboard

| Scrappers Classifieds
  1. #1
    Hurrikane started this thread.
    Hurrikane's Avatar
    SMF Badges of Honor


    Member since
    Jun 2011
    Location
    South Park,PA
    Posts
    172
    Thanks
    95
    Thanked 155 Times in 66 Posts

    Vintage Motherboard

    Accepting offers


  2. The Following 2 Users say Thank You for This Post by Hurrikane:



  3. #2
    FLimits's Avatar
    SMF Badges of Honor

    Member since
    Jan 2014
    Location
    NY
    Posts
    459
    Thanks
    654
    Thanked 598 Times in 271 Posts
    OK, Mr. Hurrikane, here's your board: BEK-3709

    Do you have the AMD 386DX-40 processor on there? Any idea if the board is working?

    Your board is very similar to a Biostar 386DX-40 board that was popular. The Intel 80386 line stopped at 33 MHz, but AMD released a 386DX (and a 386SX) that ran at 40 MHz. Systems based on AMD's 386-40 were low-cost competitors to PC's using Intel's 486SX-25. The 486's were faster, but often not by so much that the cost difference was easy to justify. In one head-to-head comparison of 15 PC's of each type, the 486SX-25's were 10% faster on average but 40% more expensive. (The full article is at AM386DX-40 vs i486SX-25)

    Here's a comparison of a maxed-out AMD 386DX-40 system vs. an Intel 486SX-25 playing DOOM:

    Last edited by FLimits; 08-17-2014 at 02:22 PM.

  4. The Following 7 Users say Thank You for This Post by FLimits:


  5. #3
    Sirscrapalot's Avatar
    SMF Badges of Honor


    Member since
    Mar 2012
    Location
    A sandbar off the atlantic..OBX,NC
    Posts
    6,123
    Thanks
    11,885
    Thanked 8,784 Times in 3,854 Posts
    Castle wolfenstein?

    I miss doom.

    That is all.

    Sirscrapalot - having flashbacks

  6. The Following 3 Users say Thank You for This Post by Sirscrapalot:


  7. #4
    Hurrikane started this thread.
    Hurrikane's Avatar
    SMF Badges of Honor


    Member since
    Jun 2011
    Location
    South Park,PA
    Posts
    172
    Thanks
    95
    Thanked 155 Times in 66 Posts

    and another. AM 386 SX-25

  8. The Following User Says Thank You to Hurrikane for This Post:


  9. #5
    FLimits's Avatar
    SMF Badges of Honor

    Member since
    Jan 2014
    Location
    NY
    Posts
    459
    Thanks
    654
    Thanked 598 Times in 271 Posts
    This is a good one! That's the motherboard from a Tandy 1000 RSX, the last of the popular Tandy 1000 line. (It's also possible that it's from a 2500 RSX, which used the same board but not all the same chips. I'd need closeup photos to be sure.) The design of the board is a bit weird -- it's smaller than a piece of letter-size paper, and it has just one 16-bit ISA slot, which is parked right in the middle of everything. And the 1000 RSX is a pretty weird computer:



    I don't know if you can tell from this picture, but the hard drive is actually screwed directly onto the bottom of the case! I don't think I've ever seen that done in any other computer. The big black bracket that's attached to the case at a 45° angle is there to support the card that's inserted into the ISA slot. When you see that, you have to wonder why a little card like that would be supported by such a hefty metal bracket. There is a clue: Since the mainboard has just one expansion slot, that probably is supposed to hold a daughterboard, or riser card, which has a normal number of expansion slots on it. Instead of expanding horizontally with various cards plugged directly into a large motherboard, the computer would expand vertically, with cards stacked parallel to the mainboard. And in fact, there was a riser card for this computer, which the user would plug into his one and only ISA expansion slot. But this is where the RSX's design gets really wacky. The riser card contained just 2 ISA slots. So to give their customer a measly 2 expansion slots, instead of just putting them on the motherboard, Tandy incurred the extra costs to produce a separate riser card and install 3 ISA connectors. At the top of the next picture, you can see the riser card with its 2 (!!) empty ISA slots:



    I really can't figure out why Tandy didn't just put both slots on the motherboard. I do know, though, why they put only 2 slots on the riser card: They couldn't expand any further vertically and still fit everything inside the 1000 RSX's case. They had given it a slimline case, and the machine was only about 3" tall! Apparently, there was another company that did make a riser card with more slots for this Tandy. Anyone who bought that card just had to leave the top off their computer case so they could use it. ¯\_(ツ)_/¯



    In spite of its quirks, the Tandy 1000 RSX is very collectible, in part because it's the last Tandy 1000 model and includes their 3-voice sound chip. You don't have the rest of the computer over there somewhere, do you? A collector would buy that in a heartbeat!


    [Edit] Almost forgot to give credit for those photos, which are not mine: http://www.oldskool.org/guides/tvdog/RLRLX.html
    Last edited by FLimits; 08-24-2014 at 03:19 PM.

  10. The Following 3 Users say Thank You for This Post by FLimits:



  11. Similar threads on the Scrap Metal Forum

    1. Watch out for this motherboard!
      By FLimits in forum E-Waste Grading and Identification
      Replies: 17
      Last Post: 03-13-2016, 09:32 PM
    2. Motherboard grading
      By johnuppy in forum E-Waste Grading and Identification
      Replies: 2
      Last Post: 02-27-2014, 09:42 PM
    3. motherboard break down
      By bigbade in forum Scrap Metal Questions and Answers
      Replies: 5
      Last Post: 11-27-2011, 12:41 AM
    4. motherboard break down
      By bigbade in forum Dismantling, Breaking Down & Maximizing Scrap
      Replies: 1
      Last Post: 11-26-2011, 01:44 PM
    5. Parts of a Motherboard
      By Mechanic688 in forum General Electronics Recycling
      Replies: 0
      Last Post: 11-10-2011, 09:06 PM

Thread Information

Users Browsing this Thread

There are currently 1 users browsing this thread. (0 members and 1 guests)

 
Browse the Most Recent Threads
On SMF In THIS CATEGORY.





OR

Bookmarks

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •  

The Scrap Metal Forum

    The Scrap Metal Forum is the #1 scrap metal recycling community in the world. Here we talk about the scrap metal business, making money, where we connect with other scrappers, scrap yards and more.

SMF on Facebook and Twitter

Twitter Facebook