Results 1 to 8 of 8

Need help grading these telephone boards

| E-Waste Grading and Identification
  1. 08-01-2012, 12:55 PM #1
    HyderConsulting
    HyderConsulting is offline Metal Recycling Entrepreneur
    HyderConsulting started this thread.
    SMF Badges of Honor
    Member since
    Jul 2012
    Location
    Cleveland, TN
    Posts
    30
    Thanks
    0
    Thanked 18 Times in 9 Posts

    Need help grading these telephone boards

    I'm getting in quite a few telephone type circuit boards lately and they are a little more difficult to grade out. Any help would be appreciated. I've got six different boards shown here with the backside showing on the the second and fourth board if I have my photos lined up right. The last board isn't telephone. Let me know what you think. Regards, Chris.

    http://i1162.photobucket.com/albums/...ing/board1.jpg
    http://i1162.photobucket.com/albums/...ing/board2.jpg
    http://i1162.photobucket.com/albums/...d2backside.jpg
    http://i1162.photobucket.com/albums/...ing/board3.jpg
    http://i1162.photobucket.com/albums/...ing/board4.jpg
    http://i1162.photobucket.com/albums/...d4backside.jpg
    http://i1162.photobucket.com/albums/...ing/board5.jpg
    http://i1162.photobucket.com/albums/...ing/board6.jpg

    Last edited by HyderConsulting; 08-01-2012 at 01:43 PM.
    Register to reply. Register To Reply

  2. The Following User Says Thank You to HyderConsulting for This Post:

    sdwyz74
  3. 08-01-2012, 12:55 PM

  4. 08-01-2012, 01:44 PM #2
    HyderConsulting
    HyderConsulting is offline Metal Recycling Entrepreneur
    HyderConsulting started this thread.
    SMF Badges of Honor
    Member since
    Jul 2012
    Location
    Cleveland, TN
    Posts
    30
    Thanks
    0
    Thanked 18 Times in 9 Posts
    Sorry about that. They are here now. I'm better at dismantling computers than operating them!

  5. The Following User Says Thank You to HyderConsulting for This Post:

    sdwyz74
  6. 08-01-2012, 08:46 PM #3
    PartTimeScrapper
    PartTimeScrapper is offline
    PartTimeScrapper's Avatar
    SMF Badges of Honor
    Member since
    Aug 2011
    Location
    Morrison, Colorado
    Posts
    3,400
    Thanks
    1,004
    Thanked 3,256 Times in 1,335 Posts
    My guess would be mid grade? $1.50 a pound or so? I am sure someone better versed then I will chime in soon.
    WWW.PTSRECYCLING.COM http://www.scrapmetalforum.com/scrap...rap-value.html
    http://www.scrapmetalforum.com/scrap...ste-scrap.html

  7. The Following User Says Thank You to PartTimeScrapper for This Post:

    sdwyz74
  8. 08-01-2012, 10:26 PM #4
    happyscraper
    happyscraper is offline
    happyscraper's Avatar
    SMF Badges of Honor
    Member since
    Feb 2012
    Location
    spring hill,fl
    Posts
    2,864
    Thanks
    350
    Thanked 1,371 Times in 847 Posts
    They look like mid grade to me but then again I not an expert.

  9. The Following User Says Thank You to happyscraper for This Post:

    sdwyz74
  10. 08-01-2012, 10:31 PM #5
    Scrapcrazy
    Scrapcrazy is offline Metal Recycling Entrepreneur
    Scrapcrazy's Avatar
    SMF Badges of Honor
    Member since
    Jul 2012
    Location
    Oklahoma
    Posts
    321
    Thanks
    153
    Thanked 321 Times in 125 Posts
    I always wish the best for everyone and I'd like to say mid grade as well but I could see a buyer trying to grade them as low grade. Let's wait and see which buyer chimes in and offers you mid grade. And if he happens to want to call them high grade I have 1000 pounds I'd like to sell him.
    Sweat is the cologne of success!

  11. The Following User Says Thank You to Scrapcrazy for This Post:

    sdwyz74
  12. 08-02-2012, 12:04 AM #6
    Jeremiah
    Jeremiah is offline
    Jeremiah's Avatar
    SMF Badges of Honor
    Member since
    Dec 2011
    Location
    Virginia
    Posts
    437
    Thanks
    147
    Thanked 381 Times in 138 Posts
    The OP was reading my mind. Just got 65 phones with boards that look like this. I would think at least mid grade for sure. After all the the RJ11 ends are gold plated

  13. The Following User Says Thank You to Jeremiah for This Post:

    sdwyz74
  14. 08-02-2012, 12:41 AM #7
    BRASSCATCHER
    BRASSCATCHER is offline
    BRASSCATCHER's Avatar
    SMF Badges of Honor
    Member since
    Feb 2012
    Posts
    2,476
    Thanks
    3,436
    Thanked 3,965 Times in 1,383 Posts
    Sorry for the hijack--Jeremiah i may have someone for those will keep you updated. This is the last shot and after this i tear them apart.
    I won't be wronged. I won't be insulted. I won't be laid a-hand on. I don't do these things to other people, and I require the same from them.” John Wayne-- The Shootist

    NEWBS READ THIS THREAD ABOUT REFINING!!!!
    http://www.scrapmetalforum.com/off-t...ning-read.html

  15. The Following 2 Users say Thank You for This Post by BRASSCATCHER:

    Jeremiah, sdwyz74
  16. 08-02-2012, 04:59 PM #8
    Dunemaul
    Dunemaul is offline Crt & Ewaste Specialist
    Dunemaul's Avatar
    SMF Badges of Honor
    Member since
    Nov 2011
    Location
    East Orlando FL
    Posts
    1,064
    Thanks
    157
    Thanked 560 Times in 301 Posts
    Im interested in buying these boards as Low grade motherboards Pm me and we can talk.
    Born to think, destine to succeed.
    Register to reply. Register To Reply

  17. The Following User Says Thank You to Dunemaul for This Post:

    sdwyz74

    18. Similar threads on the Scrap Metal Forum

    1. Help Grading these boards...
      By ScrappinRed in forum E-Waste Grading and Identification
      Replies: 6
      Last Post: 05-21-2014, 12:27 AM
    2. Grading Electronic Boards and Parts
      By Mechanic688 in forum E-Waste Grading and Identification
      Replies: 40
      Last Post: 12-15-2013, 06:29 AM
    3. Need some help grading some boards
      By spoiler73 in forum A Day in the Life of a Scrapper
      Replies: 3
      Last Post: 06-19-2012, 05:55 PM
    4. Need some help grading these boards.
      By node1tech in forum E-Waste Grading and Identification
      Replies: 12
      Last Post: 05-31-2012, 04:48 PM
    5. There is so much guess work in grading boards for beginners like me
      By Jeremiah in forum E-Waste Grading and Identification
      Replies: 10
      Last Post: 01-29-2012, 05:57 AM

« Board grading question | Power supply boards? »

Thread Information

Users Browsing this Thread

There are currently 1 users browsing this thread. (0 members and 1 guests)

 
Browse the Most Recent Threads
On SMF In THIS CATEGORY.




OR

Bookmarks

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •  

Forum Rules


The Scrap Metal Forum

    The Scrap Metal Forum is the #1 scrap metal recycling community in the world. Here we talk about the scrap metal business, making money, where we connect with other scrappers, scrap yards and more.

SMF Recommended Links

SMF on Facebook and Twitter

Twitter Facebook