Results 1 to 19 of 19

need opinion of selling escrap

| Telecom Recycling - Cell phones, tablets, PDAs etc
  1. #1
    BUNTONGM started this thread.
    SMF Badges of Honor

    Member since
    Nov 2015
    Location
    Orlando, Florida
    Posts
    10
    Thanks
    0
    Thanked 10 Times in 3 Posts

    need opinion of selling escrap

    I found this e scrap buying website that a buddy of mine uses regularly and the prices on their e buying list seems pretty fair to me. I know they are a legit company because my buddy uses them all the time. I live in florida and I think its worth it for the lower part of the US so shipping out the items wont cost too much as to sending it up north to the other companies that i know of. I have seen some better prices elseware but the cost to ship to them would cost me twice as much to the other places... Any opinions?



    404 - Page Not Found is the site.


  2. #2
    matador's Avatar
    SMF Badges of Honor

    We purchase laptop computers and many components for greater than scrap value. We offer a shipping reimbursement program.replies

    Member since
    Nov 2013
    Location
    Big Wonderful Wyoming
    Posts
    2,310
    Thanks
    1,813
    Thanked 3,204 Times in 1,450 Posts
    We don't know what you're selling, so your mileage may vary.

    Low grade boards aren't worth shipping, but their RAM prices are a joke. They're paying half of what some of our buyers here on the forum are. I've shipped 30 pounds of RAM in a large flat rate box (Around $17)- it's usually worth shipping.

    I'd go for one of the buyers here. The prices are better, and shipping isn't too bad (Some of the buyers offer a discount).
    More than Scrap Value Shipment Tips: http://www.scrapmetalforum.com/scrap...tml#post242349

  3. The Following 5 Users say Thank You for This Post by matador:


  4. #3
    webuyselltradestuff's Avatar
    SMF Badges of Honor

    Member since
    May 2013
    Location
    Watkinsville, GA
    Posts
    950
    Thanks
    131
    Thanked 1,284 Times in 583 Posts
    most of their ewaste prices are crap. Last time I sent a load...I think it was 150 lbs in 3 boxes to eWasted form GA...it ran me .30/lb. I sent mid grade an up to him and Mario's prices smoked most others. There are a few things I do send to others and one in particular that is a buyer on here (he had KILLER prices on the monitor boards (the X/Y board I believe it was), so sending those to him.

    Check their prices against yours....use Ewasted's shipping rates...they are better than your most likely. Bet you will find you are STILL on the upside...

    AGAIN, this is my reasonably extensive experience, YMMV
    PROFIT is made when you BUY/ACQUIRE NOT when you sell

  5. The Following 4 Users say Thank You for This Post by webuyselltradestuff:


  6. #4
    sledge's Avatar
    SMF Badges of Honor


    Member since
    Nov 2012
    Location
    Central Indiana
    Posts
    2,717
    Thanks
    4,534
    Thanked 4,240 Times in 1,609 Posts
    Looks like that guy is making roughly 50% margin and in a lot of cases.. BETTER than 50% when he re-sells everything upstream from his buys!
    I'm so into scrapping.. When my Steel Toe Boots Wear out, I cut the Steel out of them and recycle the Toe!

  7. The Following User Says Thank You to sledge for This Post:


  8. #5
    BUNTONGM started this thread.
    SMF Badges of Honor

    Member since
    Nov 2015
    Location
    Orlando, Florida
    Posts
    10
    Thanks
    0
    Thanked 10 Times in 3 Posts
    Good to know thanks all ill keep looking

  9. #6
    matador's Avatar
    SMF Badges of Honor

    We purchase laptop computers and many components for greater than scrap value. We offer a shipping reimbursement program.replies

    Member since
    Nov 2013
    Location
    Big Wonderful Wyoming
    Posts
    2,310
    Thanks
    1,813
    Thanked 3,204 Times in 1,450 Posts
    There are a couple of well known buyers on here- one was already mentioned in this thread. He offers prepaid shipping, which is worth it for lots that are fairly large. For the really large loads, we have an excellent person on here in the buyer's section that can help to arrange LTL pallet shipping. I've used him for the 1000# lots, Ewasted's prepaid shipping for the 200-300# lots, and if it's just RAM, you'd be amazed at what I can cram into a large flat rate box....

  10. The Following 4 Users say Thank You for This Post by matador:


  11. #7
    logansryche's Avatar
    SMF Badges of Honor


    Member since
    Sep 2014
    Location
    Jamestown, TN
    Posts
    1,215
    Thanks
    1,043
    Thanked 564 Times in 367 Posts
    Outside of Ben Weitsman/Upstate Shredding(because I'm always in constant contact with them), I wouldn't trust any other buyers except the ones on here. They've been doing this a while and know what's what. Something feels off about their site...

    The Foxy E-Scrapper
    Buy/Sell Thread: http://www.scrapmetalforum.com/scrap...ents-more.html


  12. The Following User Says Thank You to logansryche for This Post:


  13. #8
    Mechanic688's Avatar
    SMF Badges of Honor



    Member since
    Mar 2011
    Location
    Warsaw , Ind. In the heart of the lakes, and down the street from the hotel where Al Capone stayed.
    Posts
    9,568
    Thanks
    11,247
    Thanked 10,730 Times in 4,728 Posts
    That company looks to be a middleman.
    P & M Recycling - Specializing in E-Waste Recycling.
    If you enjoy your freedom, thank a vet.

  14. The Following 4 Users say Thank You for This Post by Mechanic688:


  15. #9
    SMF Badges of Honor



    Member since
    Jul 2011
    Location
    Jacksonville, NC
    Posts
    4,917
    Thanks
    15,632
    Thanked 5,861 Times in 2,713 Posts
    If you can graduate to pallet loads you will discover some real savings on shipping. I advise holding onto what you have for now. Study the threads both the ewaste and the buyers and make your well informed decision. Good luck, work hard. Mike
    "Profit begins when you buy NOT when you sell." {quote passed down to me from a wise man}

    Now go beat the copper out of something, Miked

  16. The Following User Says Thank You to miked for This Post:


  17. #10
    Sirscrapalot's Avatar
    SMF Badges of Honor


    Member since
    Mar 2012
    Location
    A sandbar off the atlantic..OBX,NC
    Posts
    6,123
    Thanks
    11,885
    Thanked 8,784 Times in 3,854 Posts
    Even if you don't think your interested in a thread...you can find some good, help advice.

    This is why we say..READ READ READ and when your eyes are bleeding an your ready to gouge your eyes out with the arm of a barbie doll...READ SOME MORE! The tips an tricks to pallet loads, boxed loads, whatever loads, is all here an for the taking. You just have to wade out there an find it.

    Sirscrapalot - Thinking is one thing no one has ever been able to tax. - Charles Kettering

  18. The Following 5 Users say Thank You for This Post by Sirscrapalot:


  19. #11
    eesakiwi's Avatar
    SMF Badges of Honor



    Member since
    Dec 2010
    Location
    NZ
    Posts
    2,531
    Thanks
    2,909
    Thanked 2,556 Times in 1,227 Posts
    Just a quick question about sorting escrap.

    I got the impression from one escrap buyers site that "if boards are not seperated properly, its going to cost the seller a lot of his profits"
    The last thing they wanted to deal with was 'A fruit salad of escrap'......

    So, I know to seperate all of the 'Hard drive boards' from the 'CD ROM boards' into seperate boxes.

    But, should I sperate all of the 'Hard drive boards' into 'Identical Hard Drive boards' and put them in plastic bags and then put all of those bags into the same box, labeled "Hard drive boards - seperated by shape" ?
    (shape - model - sort - production run..??)

    I get the impression they can find out exactly the amount of Gold/precious metals in each production run.
    And if they seperate all of the production runs, they can then tell exactly how much Gold they are going to get out of them.
    By doing this they do not 'over reclaim' their extraction of Gold from each run.

    So, 1, Just seperate all the 'Hard drive boards' into one box. All mixed up.

    2. Seperate all of the 'Hard drive boards' into seperate catagorys based on shape, and put all of the hard drive board catagorys into their own box labeled 'Hard drive boards' as before.

  20. The Following User Says Thank You to eesakiwi for This Post:


  21. #12
    SMF Badges of Honor



    Member since
    Jul 2011
    Location
    Jacksonville, NC
    Posts
    4,917
    Thanks
    15,632
    Thanked 5,861 Times in 2,713 Posts
    Quote Originally Posted by eesakiwi View Post
    Just a quick question about sorting escrap.

    I got the impression from one escrap buyers site that "if boards are not seperated properly, its going to cost the seller a lot of his profits"
    The last thing they wanted to deal with was 'A fruit salad of escrap'......

    So, I know to seperate all of the 'Hard drive boards' from the 'CD ROM boards' into seperate boxes.

    But, should I sperate all of the 'Hard drive boards' into 'Identical Hard Drive boards' and put them in plastic bags and then put all of those bags into the same box, labeled "Hard drive boards - seperated by shape" ?
    (shape - model - sort - production run..??)

    I get the impression they can find out exactly the amount of Gold/precious metals in each production run.
    And if they seperate all of the production runs, they can then tell exactly how much Gold they are going to get out of them.
    By doing this they do not 'over reclaim' their extraction of Gold from each run.

    So, 1, Just seperate all the 'Hard drive boards' into one box. All mixed up.

    2. Seperate all of the 'Hard drive boards' into seperate catagorys based on shape, and put all of the hard drive board catagorys into their own box labeled 'Hard drive boards' as before.
    1. ALL hard drive boards together. Mother boards can be separated by different types. I put very similar boards together.

    The REAL answer is as always its entirely up to YOUR buyer. Mike

  22. The Following 2 Users say Thank You for This Post by miked:


  23. #13
    mjg1021's Avatar
    SMF Badges of Honor


    Member since
    Nov 2015
    Location
    18054
    Posts
    41
    Thanks
    34
    Thanked 48 Times in 19 Posts
    Quote Originally Posted by matador View Post
    there are a couple of well known buyers on here- one was already mentioned in this thread. He offers prepaid shipping, which is worth it for lots that are fairly large. For the really large loads, we have an excellent person on here in the buyer's section that can help to arrange ltl pallet shipping. I've used him for the 1000# lots, ewasted's prepaid shipping for the 200-300# lots, and if it's just ram, you'd be amazed at what i can cram into a large flat rate box....

    hahahahahahahahaha
    Scrap long and prosper

  24. #14
    SMF Badges of Honor



    Member since
    Jul 2011
    Location
    Jacksonville, NC
    Posts
    4,917
    Thanks
    15,632
    Thanked 5,861 Times in 2,713 Posts
    Quote Originally Posted by mjg1021 View Post
    hahahahahahahahaha
    ??? I don't understand your point. Mike

  25. The Following User Says Thank You to miked for This Post:


  26. #15
    mjg1021's Avatar
    SMF Badges of Honor


    Member since
    Nov 2015
    Location
    18054
    Posts
    41
    Thanks
    34
    Thanked 48 Times in 19 Posts
    Quote Originally Posted by miked View Post
    ??? I don't understand your point. Mike
    how much you can get in a box...I thought it was funny, seems stupid now my bad

  27. #16
    SMF Badges of Honor



    Member since
    Jul 2011
    Location
    Jacksonville, NC
    Posts
    4,917
    Thanks
    15,632
    Thanked 5,861 Times in 2,713 Posts
    Quote Originally Posted by mjg1021 View Post
    how much you can get in a box...I thought it was funny, seems stupid now my bad
    No problem and if you are interested in the question of how much should you put into a box to ship ewaste is answered in several threads. I wish I could tell you which ones.

    So why would you want to know how much weight to put into a Fedex box?? Well if it over a certain weight you pay an extra charge. My recollection is about 65lbs is at or near the mark not to go over but its best to do you own research.

    By the way these numbers are not easy to find on Fedex's website. Good luck, Mike

  28. #17
    matador's Avatar
    SMF Badges of Honor

    We purchase laptop computers and many components for greater than scrap value. We offer a shipping reimbursement program.replies

    Member since
    Nov 2013
    Location
    Big Wonderful Wyoming
    Posts
    2,310
    Thanks
    1,813
    Thanked 3,204 Times in 1,450 Posts
    68 pounds is ideal for FedEx.

    For RAM, my record is 34 pounds in the large flat rate box. It was as solid as a brick, but some of my RAM fell over. If it was all perfectly aligned, I think I could have put 36 or 37 pounds in there. For $17, that's not bad!

  29. The Following User Says Thank You to matador for This Post:


  30. #18
    BUNTONGM started this thread.
    SMF Badges of Honor

    Member since
    Nov 2015
    Location
    Orlando, Florida
    Posts
    10
    Thanks
    0
    Thanked 10 Times in 3 Posts
    I checked back at the website and most of the prices payed out increase since the last time i saw it.

  31. #19
    matador's Avatar
    SMF Badges of Honor

    We purchase laptop computers and many components for greater than scrap value. We offer a shipping reimbursement program.replies

    Member since
    Nov 2013
    Location
    Big Wonderful Wyoming
    Posts
    2,310
    Thanks
    1,813
    Thanked 3,204 Times in 1,450 Posts
    These are the current prices from one of our buyers. That buyer is still low- RAM is the same price, too.

    Quote Originally Posted by xxxx;

    PRICING EFFECTIVE
    11/12/2015

    PRINTED CIRCUIT BOARDS
    Please remove batteries and excess AL and Steel
    PRICE/LB MATERIAL
    $1.40 Motherboards Small Socket (All Colors - P4 and Newer)
    $2.60 Motherboards Large Socket (All Colors - Slot, P3 and older)
    $1.80 Motherboards Large Socket Low Grade (All Colors - primarily socket type 462)
    $1.60 Finger Board Trimmed/Devalued
    $3.25 Finger Boards (Only need to remove OVERSIZED heatsinks, battery... metal bracket is OK)
    $3.45 Dual Socket Server Boards - Large Socket
    $2.05 Dual Socket Server Boards - Small Socket
    $3.45 to 6.00+ Telecom (Paid on Sort)
    $2.60 CD/DVD Boards (please remove ribbon wire and brown board if attached)
    $3.45+ Tape Drive Boards (Paid on sort)
    $3.00 Laptop Motherboard Boards

    HIGH VALUE PRINTED CIRCUIT BOARDS
    PRICE/LB MATERIAL
    $4.75 RAMBUS (Memory with METAL Enclosure)
    $7.85 Hard Drive Boards (Sorting fee of $.30 per lb. Hard Drive Boards paid on sort once removing Floppy, CD/DVD and Media Boards)
    $7.85 Cell Phone Boards CLEAN (please remove excess Plastic, Steel, Screens, Aluminum and Battery)
    $-.30/lb Memory Mixed (Sorting fee of $.30 per lb. Memory paid on sort at pricing below)
    $12.25 Gold Memory
    $6.00 Silver/Tin Memory
    $30.00 Gold Fingers (Pricing is for quality cut trim. Little to no Green, otherwise deduction)
    $10.50 Slot Processor

    OTHER PRECIOUS METAL ITEMS
    PRICE/LB MATERIAL
    $0.45 Gold Connectors
    $3.60 Cell Phones w/o battery
    $3.75 IC Chips

    CPUs (Must be Sorted)
    PRICE/LB MATERIAL
    $90.00 Intel 386 and 486
    $65.00 Motorola
    $60.00 Pentium Pro Gold Caps
    $30.00 Cyrix/IBM/VIA Gold Cap
    $27.00 Pentium Ceramic
    $23.00 AMD Ceramic Clean (without Al. Cap)
    $25.00 Black Fiber CPU
    $11.00 Green/Brown Fiber without Heatsink
    $5.25 Green Fiber with Heatsink - Pins
    $3.00 Green Fiber with Heatsink - Pinless

    COMPUTER/SERVER PARTS
    PRICE/LB MATERIAL
    $0.60 Hard Drives Complete
    $0.45 Hard Drives Complete (Bent, Punched, Crushed - NOT Shredded)
    $0.30 Hard Drives w/o Boards
    $0.23 Power Supply w/ Wire
    $0.14 Power Supply w/o Wire
    $0.13 Mixed Floppy/CD/DVD Drives

    OTHER ITEMS
    PRICE/LB MATERIAL
    $1.10 Laptops Complete
    $0.70 Incomplete laptops (Must have Motherboard)
    $0.80 Li Ion Laptop (Exposed terminals MUST be taped)
    $-.30 Terminal Tape Fee
    $0.60 Li Ion Cell (Exposed terminals MUST be taped)
    $0.17 AC Adapter w/ Wire
    $0.11 AC Adapter w/o Wire
    $0.40 Mixed Computer Wire
    $0.70 Ribbon wire with ends (Must be PRESORTED from other wire)
    $0.70 Cat5 with ends (Must be PRESORTED from other wire)
    $0.00 Mixed Computer Plastic (NO METAL!)
    $0.30 Clean Aluminum Heatsink
    $0.65 Clean Cu/Al Heatsink
    $2.00 15" LCD [per UNIT] DESKTOP LCD MONITORS - with or without BASE - No screen bleeding, gouges, Cracks, Cut cables, water damage. Must be monitor, NOT just a panel
    $5.00 17"+ LCD [per UNIT] DESKTOP LCD MONITOR - with or without BASE - No screen bleeding, gouges, Cracks, Cut cables, water damage . Must be monitor, NOT just a panel
    $3.00 Laptop Screens [per UNIT] Must be in case, pass light test, be in tact, no bleeding, water damage or cracks. Cut wire -$1.00/unit - NO Netbook Screens - ONLY for Laptop Screens

    Prices are subject to change without notice.
    Pricing is determined by date of RECEIPT of material unless otherwise noted.


  32. Similar threads on the Scrap Metal Forum

    1. That's a lot of copper (at least in my opinion)...
      By DakotaRog in forum A Day in the Life of a Scrapper
      Replies: 9
      Last Post: 07-02-2015, 11:59 AM
    2. This thread is a serious one - New member selling escrap
      By DannyD in forum Introduce yourself
      Replies: 13
      Last Post: 11-26-2014, 06:29 AM
    3. Opinion on this ?
      By gamedayron in forum A Day in the Life of a Scrapper
      Replies: 22
      Last Post: 04-19-2014, 08:19 PM
    4. Being an EScrap collection site vs EScrap recycler...........
      By HVRC in forum General Electronics Recycling
      Replies: 6
      Last Post: 08-17-2013, 08:40 PM

Thread Information

Users Browsing this Thread

There are currently 1 users browsing this thread. (0 members and 1 guests)

 
Browse the Most Recent Threads
On SMF In THIS CATEGORY.





OR

Tags for this Thread

Bookmarks

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •  

The Scrap Metal Forum

    The Scrap Metal Forum is the #1 scrap metal recycling community in the world. Here we talk about the scrap metal business, making money, where we connect with other scrappers, scrap yards and more.

SMF on Facebook and Twitter

Twitter Facebook