Results 1 to 15 of 15
  1. #1
    easyrecycle started this thread.
    SMF Badges of Honor


    Member since
    May 2011
    Location
    Dallas TX
    Posts
    1,979
    Thanks
    158
    Thanked 1,182 Times in 518 Posts

    Dash cam system being tested - low cost

    This is something I have been thinking and slowly working on.

    Right now I think I have found the set up I am going to use that is both low cost but high power.

    I am doing some more testing on this system and once I have that done I will report back here on my findings.

    But I think anyone who is driving as much as we do..and or "scrapping" having a dash cam and or a cam we can have recording us at all times will not only be good for when we are driving but when we are picking stuff up. It will give proof of where we picked it up at and how we where just "driving" around when we saw it.

    On another note if any damage was found before during or after you where at someones place (home or company) you will have video showing that one..the damage was there before hand or two the damage was NOT there when you left an there for it happened after you where gone. Its very hard to disregard a video tape in many ways.

    Long story short. I am "jumping" the gun on what I have been working on so you all can start thinking about it. Once I worked out the whole system I will post here again...and on my YouTube page on this system. So anyone who has subed my page will get the info once it hits there.

    P.s if you are using a video system in your truck, suv, car or space ship. Share the info and your setup. I am sure I am not the only one who has been working on this.
    My company name was Easy Recycle but has since been closed
    My Name Stephan Harz
    My YouTube page


  2. #2
    TheHoss's Avatar
    SMF Badges of Honor

    Member since
    Mar 2011
    Location
    The tater state
    Posts
    863
    Thanks
    1,112
    Thanked 840 Times in 279 Posts
    Currently using one on my spaceship. 100 camera's in total. Good for those sneak asteroid attacks, star court is a pain!

  3. #3
    Dumpster-Dee's Avatar
    SMF Badges of Honor



    Member since
    Feb 2011
    Location
    SW Georgia
    Posts
    1,775
    Thanks
    2,286
    Thanked 838 Times in 457 Posts
    lol Hoss. Don't know whether it's the copper or the remedy, but somethings making you giddy !!! Time for beddie bye !!

  4. #4
    SMF Badges of Honor


    Member since
    Jun 2011
    Posts
    47
    Thanks
    3
    Thanked 4 Times in 3 Posts
    turns out it was a laser sand filter

  5. #5
    SMF Badges of Honor


    Member since
    Jun 2011
    Posts
    47
    Thanks
    3
    Thanked 4 Times in 3 Posts
    Also to stay on topic. Since your truck probably isn't always facing the area your working and can't come inside of you. You might want to consider a person mounted camera. Perhaps some thing like a button camera. Something inconspicuous, but effective in preventing you being held liable for any damages that were already inside someones home or on there property.

  6. #6
    easyrecycle started this thread.
    SMF Badges of Honor


    Member since
    May 2011
    Location
    Dallas TX
    Posts
    1,979
    Thanks
    158
    Thanked 1,182 Times in 518 Posts
    Ok that plan failed...have to work on another idea....my idea was using a webcam and building a stand that I can mount it into my truck....the issue is....making a stand that will hold it still to get clean video on.

    But I am going to mess with this some more but kinda have to put it onto the back burner once again....another of my projects is now done and fully working...time to use the hell out of that to turn a profit on it...I have over 2grand invested on that deal lol...about time I am done tossing money on it and it starts MAKING money.

  7. #7
    SMF Badges of Honor


    Member since
    Jun 2011
    Posts
    47
    Thanks
    3
    Thanked 4 Times in 3 Posts
    Well button cams aren't expensive at all. http://www.dynaspy.com/allinone-shir...amp-p-216.html check that one out. $100.00 and youre covered

  8. #8
    easyrecycle started this thread.
    SMF Badges of Honor


    Member since
    May 2011
    Location
    Dallas TX
    Posts
    1,979
    Thanks
    158
    Thanked 1,182 Times in 518 Posts
    Quote Originally Posted by thrsxs View Post
    Well button cams aren't expensive at all. http://www.dynaspy.com/allinone-shir...amp-p-216.html check that one out. $100.00 and youre covered
    I would brake it in about 2hours....from smashing it and sweating on top of it.

    When I am working around a job site when I go there to take a look at it when I am bidding on the job...I take alot of photos of every part...when I am working on the clean out/haul out..I take photos when work is being done (before and after) and when the job is all done...I take photos again.

    This covers your butt...but at the same time will show your client your/companies hard work. Sometimes your clients before and after (some times it looks like you did nothing when in fact you had.)

    I just want it for when I am driving...trust me....Dallas drivers are BAD..every day we have a car fire...one to 5 deadly car accident every month some car that parked inside some building....its fun to have the radio on in the morning to know what %#*$ crap happened...an why you are sitting still on the highway.

  9. #9
    eesakiwi's Avatar
    SMF Badges of Honor



    Member since
    Dec 2010
    Location
    NZ
    Posts
    2,531
    Thanks
    2,909
    Thanked 2,556 Times in 1,227 Posts
    I was thinking you ment a camera dome setup, like a vertical camera with a dome lens on it so it works in a 360 degree field.

    Thats all you would need for evidence, even mentioning it would shut someone up too.

  10. #10
    SMF Badges of Honor


    Member since
    Apr 2011
    Location
    Bloomington, Indiana
    Posts
    126
    Thanks
    8
    Thanked 95 Times in 37 Posts
    This is an easy concept, if I had the money to blow on electronics and the time I would do it. Just get a motion sensor camera with onboard DVR. As long as you're moving you're being recorded, and it records it's own footage. Run it off an inverter and you're done. I mean props for wanting your own set-up.

    Get a motorized turn table, add an IR sensor to it, mount a web cam to the turn table, stick on a laser pointer for guidance, get a keychain remote, and then you have a 360 degree laser guided remote controlled camera.

    There's a few ways of doing this low budget, but I'd got with the motion sensor camera with DVR. Saw one awhile back for 165 on ebay.

  11. #11
    SMF Badges of Honor

    Member since
    Dec 2021
    Location
    Faisalabad
    Posts
    1
    Thanks
    0
    Thanked 0 Times in 0 Posts
    As you are talking about dash cam testation then i am here to suggest you best webcam cover to buy at very low and reasonable prices from an online store because it will save your time and allow you to buy this product at very lowest cost , So buy this product and thanks me later. Have a GOOD day ahead. THANKS
    REGARDS
    Smith
    Last edited by smithjj; 12-18-2021 at 05:56 AM.

  12. #12
    CopperMiner's Avatar
    SMF Badges of Honor


    Member since
    Jun 2021
    Location
    Greater Montreal
    Posts
    320
    Thanks
    181
    Thanked 203 Times in 119 Posts
    Dashcam is something I am looking as well, but not just for finding goodies on the curb. I also thought to some DYI solutions, but none were good enough. Remember that dashcams are made to record on the long time and less than perfect road/weather condition. Just using an old cell phone and a static stand would not be a good idea, because they're not made for recording hour long videos. Not sure that I would use a webcam or something made for indoor use on a dashboard by a hot sunny day or when it is below freezing point.

  13. #13
    mikeinreco's Avatar
    SMF Badges of Honor


    Member since
    Dec 2011
    Location
    TENNESSEE
    Posts
    4,985
    Thanks
    1,257
    Thanked 5,023 Times in 2,351 Posts
    This is old thread haven't gopro taken care of this

  14. #14
    CopperMiner's Avatar
    SMF Badges of Honor


    Member since
    Jun 2021
    Location
    Greater Montreal
    Posts
    320
    Thanks
    181
    Thanked 203 Times in 119 Posts
    Quote Originally Posted by mikeinreco View Post
    This is old thread haven't gopro taken care of this
    Good point. GoPro is something I like, but their models are quite costly to what I saw the last time I had a look. I need to check them again if they have something cheaper.


  15. #15
    CopperMiner's Avatar
    SMF Badges of Honor


    Member since
    Jun 2021
    Location
    Greater Montreal
    Posts
    320
    Thanks
    181
    Thanked 203 Times in 119 Posts
    After something like three years, I kicked myself in the **** and I just bought a Garmin dash cam. Instructions included in the box are useless and it was hard to detect and pair it with my cellphone via a proprietary app, but it works now. Just now sure how to get a full trip in one file instead of multiple segments. Be prepared to see new videos on YT.
    NEW TO SCRAPPING? READ THIS: Build up your horde of magnetic and non-magnetic metals in two piles until you have a better understanding of the business. Magnetic material has low value and is mostly always steel / shred / short iron. Read old threads about non-magnetic metals and ewaste (and how to sort them), but don't forget that they generally have absolutely no tolerance for contamination (screw / iron / foreign material).


  16. Similar threads on the Scrap Metal Forum

    1. The Story of Money: From a Barter System to a Money System.
      By mrsamsonite in forum Off Topic Discussions
      Replies: 25
      Last Post: 01-10-2021, 10:09 PM
    2. Nationwide, Low Cost Roll Off Dumpster Rentals
      By GeorgeB in forum Non Metal Recycling
      Replies: 0
      Last Post: 09-17-2012, 09:30 PM
    3. cost of regulations
      By EcoSafe in forum Off Topic Discussions
      Replies: 1
      Last Post: 02-29-2012, 12:15 PM
    4. Low cost plastic bottle baler
      By scrapdollar in forum Non Metal Recycling
      Replies: 7
      Last Post: 01-07-2012, 09:07 PM

Thread Information

Users Browsing this Thread

There are currently 1 users browsing this thread. (0 members and 1 guests)

 
Browse the Most Recent Threads
On SMF In THIS CATEGORY.





OR

Bookmarks

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •  

The Scrap Metal Forum

    The Scrap Metal Forum is the #1 scrap metal recycling community in the world. Here we talk about the scrap metal business, making money, where we connect with other scrappers, scrap yards and more.

SMF on Facebook and Twitter

Twitter Facebook