Results 1 to 11 of 11

Finally my new truck!

| Tools and Equipment
  1. #1
    gamedayron started this thread.
    gamedayron's Avatar
    SMF Badges of Honor



    Member since
    Dec 2011
    Posts
    209
    Thanks
    386
    Thanked 246 Times in 61 Posts

    Finally my new truck!

    so after a lot of debate.. and i mean ALOT i decided to buy a 97 E250 cargo van . the asking price was 550 but the guy decided to godown to 300. i now have the van next steps are to give it the usual oil change flush the radiator blah blah and paint over the old companys decals. the best part about this all thou is that the guy i bought the van from is now partnered with my business. he runs a party tent business and me with my scrap. we work for eachother every now and then and we both advertise each others company when handing out flyers or business cards.



  2. #2
    SMF Badges of Honor




    Member since
    Mar 2012
    Location
    ks
    Posts
    2,187
    Thanks
    2,513
    Thanked 2,140 Times in 898 Posts
    Sounds sweet p
    Alvord iron and salvage
    3rd generation scrapper and dam proud of it

  3. #3
    SMF Badges of Honor



    Member since
    Jul 2011
    Location
    Jacksonville, NC
    Posts
    4,917
    Thanks
    15,632
    Thanked 5,861 Times in 2,713 Posts
    $300 for a running work van, wow cheap. Mike
    "Profit begins when you buy NOT when you sell." {quote passed down to me from a wise man}

    Now go beat the copper out of something, Miked

  4. #4
    BRASSCATCHER's Avatar
    SMF Badges of Honor


    Member since
    Feb 2012
    Posts
    2,476
    Thanks
    3,436
    Thanked 3,965 Times in 1,383 Posts
    Nice going Ron hope it runs another 100 k miles for you....did up get to joes and pick up that suff yet?
    I won't be wronged. I won't be insulted. I won't be laid a-hand on. I don't do these things to other people, and I require the same from them.” John Wayne-- The Shootist

    NEWBS READ THIS THREAD ABOUT REFINING!!!!
    http://www.scrapmetalforum.com/off-t...ning-read.html

  5. #5
    Mechanic688's Avatar
    SMF Badges of Honor



    Member since
    Mar 2011
    Location
    Warsaw , Ind. In the heart of the lakes, and down the street from the hotel where Al Capone stayed.
    Posts
    9,568
    Thanks
    11,247
    Thanked 10,730 Times in 4,728 Posts
    Good luck GD sounds like things are starting to roll for you.
    P & M Recycling - Specializing in E-Waste Recycling.
    If you enjoy your freedom, thank a vet.

  6. #6
    KzScrapper's Avatar
    SMF Badges of Honor


    Member since
    Apr 2011
    Location
    Denver Metro, CO
    Posts
    4,841
    Thanks
    7,019
    Thanked 5,792 Times in 2,417 Posts
    At that price, if had to scrap it today because it dies you still make money...nice work.
    Recyclable Material Merchant Wholesaler
    Certified Zip-Tie Mechanic
    "Give them enough so they can do something with it, but not too much that they won't do nothing."

  7. The Following User Says Thank You to KzScrapper for This Post:


  8. #7
    gamedayron started this thread.
    gamedayron's Avatar
    SMF Badges of Honor



    Member since
    Dec 2011
    Posts
    209
    Thanks
    386
    Thanked 246 Times in 61 Posts
    yeah thats the best thing about it if i scrapped it probebly make 150 - 200 dollars and brasscatcher no hes been calling me and canceling idk whats up with him

  9. #8
    SMF Badges of Honor



    Member since
    Feb 2012
    Location
    OK
    Posts
    5,731
    Thanks
    6,815
    Thanked 3,465 Times in 1,990 Posts
    while you're changing the oil, flushing radiator, good time check/change the tranny fluid too, and the rear end. Also lift the wheels to check for bearing end play, if loose adjust, if dirty, clean them and re-pack. The first thing to do as you're getting your oil etc, is grab a repair manual for that vehicle (it'll pay for itself the first time you use it ) not a bad idea to give it a thorough once over now, to avoid being broke down or crashed later. Happy driving

    inspect your steering linkage too for loose/worn steering links, and grease it well. Those have kingpins too which need inspected for play ( by grabing the tire while raised and pulling it side to side to check for play, play here is usually an indicator of loose wheel bearings though) and greased also ( grease fitting above and below the kingpin, the kingpin basically holds your steering wheels on and allows it to swivel)

    lol, also good to inspect your driveshaft for loose/worn u-joints and grease them too lol again. You check that all out now and you'll be good to go for miles, if not may be broke soon
    Last edited by Bear; 05-13-2012 at 10:16 AM.

  10. #9
    SMF Badges of Honor


    Member since
    Dec 2010
    Location
    Minnesota
    Posts
    83
    Thanks
    46
    Thanked 27 Times in 14 Posts
    I use a 95 E-250 and its an awesome vehicle for scrapping. Good luck with it.

  11. #10
    SMF Badges of Honor


    Member since
    Mar 2012
    Location
    santa rosa, ca
    Posts
    25
    Thanks
    0
    Thanked 27 Times in 4 Posts
    u can't lose for $300 if it takes a **** just scrap it sweet

  12. #11
    SMF Badges of Honor



    Member since
    May 2012
    Location
    Metro-West , Mass.
    Posts
    93
    Thanks
    54
    Thanked 95 Times in 18 Posts
    When ever I pick up an older vehicle , the first thing I do , along with oil , oil filter and radiator flush as others have suggested , is replace ALL the Belts and Hoses so I know what I have under the hood , also I don't like to do repairs on the side of the road .
    Bandit


  13. Similar threads on the Scrap Metal Forum

    1. Finally something of my own
      By rca987 in forum Off Topic Discussions
      Replies: 28
      Last Post: 07-24-2013, 01:43 AM
    2. finally got a trailer!
      By james2144 in forum A Day in the Life of a Scrapper
      Replies: 10
      Last Post: 12-01-2012, 08:10 PM
    3. finally
      By parrothead in forum More than Scrap Value
      Replies: 11
      Last Post: 09-18-2011, 06:23 PM
    4. I finally got a trailer
      By parrothead in forum Tools and Equipment
      Replies: 12
      Last Post: 08-05-2011, 03:36 AM
    5. Finally got something to do.
      By zakmattingly in forum A Day in the Life of a Scrapper
      Replies: 5
      Last Post: 07-19-2011, 12:05 AM

Thread Information

Users Browsing this Thread

There are currently 1 users browsing this thread. (0 members and 1 guests)

 
Browse the Most Recent Threads
On SMF In THIS CATEGORY.





OR

Bookmarks

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •  

The Scrap Metal Forum

    The Scrap Metal Forum is the #1 scrap metal recycling community in the world. Here we talk about the scrap metal business, making money, where we connect with other scrappers, scrap yards and more.

SMF on Facebook and Twitter

Twitter Facebook