Results 1 to 17 of 17
  1. #1
    saturninin started this thread.
    SMF Badges of Honor


    Member since
    Jul 2012
    Location
    Indiana
    Posts
    67
    Thanks
    8
    Thanked 39 Times in 17 Posts

    Maximum Amount to be made on 97 Ford Taurus GL Station Wagon

    So I have still have both cars described in previous post: Scrapping 2 Cars
    But I had some more questions about the Tausus

    Car: 1997 Ford Tausus GL Station Wagon
    Millage: 180k-200kish
    Trans: 4 Speed Automatic
    Engine: 3.0 Liter V6 w/SFI
    ----Issue: Blown Head Gasket
    Curb Weight- 3505 Pounds







    Near New Tires


    I paid $320 for the car from a friend (figured scrap value on it is about $380) so I have listed on Craigslist for $750 as is....


    The tires are near new so if I were to scrap it I would keep them and list them for like $250 on Craigslist (with rims)

    Is the $750 more than I will get via scrapping it?

    I have had several people offering lower then my asking price (what do you expect.... its Craigslist....) But I am wounding what exactly **roughly** would you think I would make off of it scrapping it/ selling parts?

    I was figuring pulling:

    CAT
    RIMS/Tires
    Radiator
    O2 sensors
    The 1 good fender
    Computers
    Mirrors
    Any Larger Motors
    Wiring
    maybe trans....
    any other thoughts?

    Thoughts on money I will make scrapping it (spending decent about of time) **rough estimate of what I would make scrapping please** compared to washing my hands of it and selling it whole to private party?


  2. #2
    corycouch's Avatar
    SMF Badges of Honor


    Member since
    Dec 2011
    Location
    jonesboro ar
    Posts
    1,405
    Thanks
    3,766
    Thanked 1,988 Times in 746 Posts
    At first glance I thought you had aluminum wheels, but I seen the holes behind so they are steel, if you have a buyer for the tires it's worth taking them off and you can get short iron for the wheels. You also have to have a way to dismount them which probably won't be free.

    That car has two cats on the passenger side behind the front wheel, about $40 apiece

    If it were mine I'd cut the cats, drain the gas, get the wheels, check under the back seat for treasure and haul it in.

    If I were you though I'd get the radiator, alternator compressor and anything bolted to the motor, you will get at worse breakage for all that stuff. Rip out the dash and door panels and the carpet and get all the wire you can. Also heater core and the little air conditioning radiator and blower motor is in the dash. Throw all the plastic in the back.

    Before my volume of cars got beyond my means I done most of them this way and just from wire alone we were getting 200+ a week.

    That Taurus wagon (it's been a while) should bring 350ish give or take 25 at my prices on the body, they are heavier than they look.

    My advice rip it apart, be careful and have fun
    expect the worst and hope for the best
    cory couch
    c & c recycling
    JUNKERS AND CLUNKERS
    (870) 897-6484

  3. The Following 4 Users say Thank You for This Post by corycouch:


  4. #3
    saturninin started this thread.
    SMF Badges of Honor


    Member since
    Jul 2012
    Location
    Indiana
    Posts
    67
    Thanks
    8
    Thanked 39 Times in 17 Posts
    Quote Originally Posted by corycouch View Post
    At first glance I thought you had aluminum wheels, but I seen the holes behind so they are steel, if you have a buyer for the tires it's worth taking them off and you can get short iron for the wheels. You also have to have a way to dismount them which probably won't be free.

    That car has two cats on the passenger side behind the front wheel, about $40 apiece

    If it were mine I'd cut the cats, drain the gas, get the wheels, check under the back seat for treasure and haul it in.

    If I were you though I'd get the radiator, alternator compressor and anything bolted to the motor, you will get at worse breakage for all that stuff. Rip out the dash and door panels and the carpet and get all the wire you can. Also heater core and the little air conditioning radiator and blower motor is in the dash. Throw all the plastic in the back.

    Before my volume of cars got beyond my means I done most of them this way and just from wire alone we were getting 200+ a week.

    That Taurus wagon (it's been a while) should bring 350ish give or take 25 at my prices on the body, they are heavier than they look.

    My advice rip it apart, be careful and have fun
    I'd sell the rims for replacements (I sometimes sell Saturn Steel Wheels on CL (once i've worn out the tires) and sell them for 2 for $35....)

    Doing what you suggest what would the total scrap price you think I would be looking at?

    $350- Shell
    $200- Tires (went low)
    $080- CATS
    $???- Wire
    $???- Radiator
    $???- Alternator/Compressor/ Other things on Engine
    $???- Heater core, air conditioning radiator, and blower motor
    ________
    $630- Shell, Tires, CATS
    $???- Other Things
    __________________
    $??? Total
    Last edited by saturninin; 02-12-2014 at 12:55 AM.

  5. #4
    SMF Badges of Honor



    Member since
    Feb 2012
    Location
    OK
    Posts
    5,731
    Thanks
    6,815
    Thanked 3,465 Times in 1,990 Posts
    Quote Originally Posted by saturninin View Post
    I'd sell the rims for replacements (I sometimes sell Saturn Steel Wheels on CL (once i've worn out the tires) and sell them for 2 for $35....)

    Doing what you suggest what would the total scrap price you think I would be looking at?

    $350- Shell
    $200- Tires (went low)
    $080- CATS
    $???- Wire
    $???- Radiator
    $???- Alternator/Compressor/ Other things on Engine
    $???- Heater core, air conditioning radiator, and blower motor
    ________
    $630- Shell, Tires, CATS
    $???- Other Things
    __________________
    $??? Total
    You're funny inin ; ) where you from?

  6. The Following 2 Users say Thank You for This Post by Bear:


  7. #5
    saturninin started this thread.
    SMF Badges of Honor


    Member since
    Jul 2012
    Location
    Indiana
    Posts
    67
    Thanks
    8
    Thanked 39 Times in 17 Posts
    Northwest, IN (Valpo Area).....

    And I'm just trying to get maximum profits off this.... **Since I've never scraped cars or that before** I've scraped Computers, strait scrap metal, and anything else I can get my hands on the side of the road.... just trying to learn the ins/outs of the best way to make the most $$$ while scrapping cars

  8. #6
    JunkLady's Avatar
    SMF Badges of Honor


    Member since
    Jan 2014
    Posts
    37
    Thanks
    0
    Thanked 7 Times in 4 Posts

    Maximum Amount to be made on 97 Ford Taurus GL Station Wagon

    Keep in mind that $350 shell price keeps dropping as u remove items(trans,wheels). I say give it a week on cl as its tax time. If you can verify good trans then yank it(easier said then done) compare salvage yard prices 1st. If they selling them for like $200 then dont bother.think $200 for steel wheels is far fetched. Other lil gems n keep it moving. Think $750 including knick knacks(will have to wait for sales). Or do nothing n quick flip for $525 cl n go make more money! I do the quick flips ALOT. Can pay $325 for a car n have my buyer pick it up for me n pay me like $425 depending. I just take the battery, pcm, crap they won't miss n keep it moving. $100 for 30 minutes...sometimes :-)
    "If it makes dollars, then it makes sense!"

  9. #7
    saturninin started this thread.
    SMF Badges of Honor


    Member since
    Jul 2012
    Location
    Indiana
    Posts
    67
    Thanks
    8
    Thanked 39 Times in 17 Posts
    Quote Originally Posted by JunkLady View Post
    Keep in mind that $350 shell price keeps dropping as u remove items(trans,wheels). I say give it a week on cl as its tax time. If you can verify good trans then yank it(easier said then done) compare salvage yard prices 1st. If they selling them for like $200 then dont bother.think $200 for steel wheels is far fetched. Other lil gems n keep it moving. Think $750 including knick knacks(will have to wait for sales). Or do nothing n quick flip for $525 cl n go make more money! I do the quick flips ALOT. Can pay $325 for a car n have my buyer pick it up for me n pay me like $425 depending. I just take the battery, pcm, crap they won't miss n keep it moving. $100 for 30 minutes...sometimes :-)
    I was saying like $250 with the brand new tires.... so less then the tires by themselves and toss in the Rims

    And that's what I'm thinking.... if I can flip it without doing anything.... but I don't want to loose out on extra $$$ that I could make if I sell it to the crusher..... This money I'm looking at using to get a nice RUST FREE car dolly down south

  10. #8
    skylinejack's Avatar
    SMF Badges of Honor


    Member since
    Jul 2011
    Location
    Baton Rouge, La.
    Posts
    827
    Thanks
    1,194
    Thanked 959 Times in 400 Posts
    Quote Originally Posted by corycouch View Post
    At first glance I thought you had aluminum wheels, but I seen the holes behind so they are steel, if you have a buyer for the tires it's worth taking them off and you can get short iron for the wheels. You also have to have a way to dismount them which probably won't be free.

    That car has two cats on the passenger side behind the front wheel, about $40 apiece

    If it were mine I'd cut the cats, drain the gas, get the wheels, check under the back seat for treasure and haul it in.

    If I were you though I'd get the radiator, alternator compressor and anything bolted to the motor, you will get at worse breakage for all that stuff. Rip out the dash and door panels and the carpet and get all the wire you can. Also heater core and the little air conditioning radiator and blower motor is in the dash. Throw all the plastic in the back.

    Before my volume of cars got beyond my means I done most of them this way and just from wire alone we were getting 200+ a week.

    That Taurus wagon (it's been a while) should bring 350ish give or take 25 at my prices on the body, they are heavier than they look.

    My advice rip it apart, be careful and have fun
    That's some Grade A, Number 1, Top notch advise/tips Cory gave you there. ^^^^^^

    Quote Originally Posted by saturninin View Post
    I'd sell the rims for replacements (I sometimes sell Saturn Steel Wheels on CL (once i've worn out the tires) and sell them for 2 for $35....)

    Doing what you suggest what would the total scrap price you think I would be looking at?

    $350- Shell
    $200- Tires (went low)
    $080- CATS
    $???- Wire
    $???- Radiator
    $???- Alternator/Compressor/ Other things on Engine
    $???- Heater core, air conditioning radiator, and blower motor
    ________
    $630- Shell, Tires, CATS
    $???- Other Things
    __________________
    $??? Total
    You're kidding, right? Maybe you would like Cory to travel from Jonesboro Ar. to your place in Indiana and just do all the work for you. Then when he's finished he can give you all the money from this little project and travel back home on his own dime. OR maybe you can do some this on your own. All by yourself. Roll up your sleeves and get to work. And learn a few things along the way. Come on, dude. You gotta put forth a little effort of your own. Nobody can tell you exactly what these things will sell for. YOU are the only that can tell us your total. After the sale.
    AMERICAN BORN, AMERICAN BRED! AND I'M PROUD TO BE AN AMERICAN!!!

  11. The Following 5 Users say Thank You for This Post by skylinejack:


  12. #9
    lousypirate's Avatar
    SMF Badges of Honor

    Member since
    Dec 2013
    Location
    Marne, MI
    Posts
    440
    Thanks
    36
    Thanked 287 Times in 138 Posts
    If you're time is free, the more you tear apart, the more you'll make in scrap. pretty simple.

    Aluminum average price .50/#
    Copper wire .75-.95/#
    Battery .25/#
    Alternator .25/#
    Starter .25/#


    figure out how fast you can do it, and see what's worth your time. The only time I play the "what's it worth" game is when I'm buying, once I have it, get it processed and gone. Put up a part out thread while you are tearing down. put up cheap prices, above scrap, below auto salvage price. what moves moves, what doesn't scrap.

    (I really shouldn't say anything because there is still some parts in the garage from my last partout.. in september. It's the same truck that I currently drive though, so I don't feel bad)

  13. The Following User Says Thank You to lousypirate for This Post:


  14. #10
    corycouch's Avatar
    SMF Badges of Honor


    Member since
    Dec 2011
    Location
    jonesboro ar
    Posts
    1,405
    Thanks
    3,766
    Thanked 1,988 Times in 746 Posts
    1st thanks skyline for the compliment

    2nd, I can't see me getting 200 for any set of tires, I had a new set of all terrains a year or so ago for $100. I get $10 a tire for good tires from my buyer, they sell them for $25. Tires for me is what's worth my time, I could get more, but that would mean dealing with dozens of phone calls and dozens of dumb@$$ questions about tires sooooo, I sell them to someone else. Bottom line I can buy a car in the time it takes to sell one set of tires or even worse waiting on a no show for two hours.

    3rd as for the take off stuff it will depend on your prices which will mainly depend on your relationship with your yard

  15. The Following 2 Users say Thank You for This Post by corycouch:


  16. #11
    sledge's Avatar
    SMF Badges of Honor


    Member since
    Nov 2012
    Location
    Central Indiana
    Posts
    2,717
    Thanks
    4,534
    Thanked 4,240 Times in 1,609 Posts
    IF I were to be gutting that car this is the approximate math:
    $320 on body (this taking into car having a bunch removed)
    $100-$125 on Tires - and would cost me $12 to have removed
    Rims would be tossed back in the car
    $80: Converters total
    $7 on the Alternator
    $5 on A/C Pump
    $35 on Wiring
    $7 bucks if you get both heater cores and rads
    $5 or so in A/C lines, condenser etc
    $12 on Battery

    $559 to $584 Ballpark
    Profit $239 to $264 at $320 Buy Price.

    But as it has been said- your BEST learning "advice" is experience. Dig in, Gut her hard and see what she brings you!
    I'm so into scrapping.. When my Steel Toe Boots Wear out, I cut the Steel out of them and recycle the Toe!

  17. The Following 4 Users say Thank You for This Post by sledge:


  18. #12
    saturninin started this thread.
    SMF Badges of Honor


    Member since
    Jul 2012
    Location
    Indiana
    Posts
    67
    Thanks
    8
    Thanked 39 Times in 17 Posts
    Quote Originally Posted by skylinejack View Post
    That's some Grade A, Number 1, Top notch advise/tips Cory gave you there. ^^^^^^

    You're kidding, right? Maybe you would like Cory to travel from Jonesboro Ar. to your place in Indiana and just do all the work for you. Then when he's finished he can give you all the money from this little project and travel back home on his own dime. OR maybe you can do some this on your own. All by yourself. Roll up your sleeves and get to work. And learn a few things along the way. Come on, dude. You gotta put forth a little effort of your own. Nobody can tell you exactly what these things will sell for. YOU are the only that can tell us your total. After the sale.
    I completely understand the "different area different prices".... but i was just looking for a bit of guidance

    Quote Originally Posted by lousypirate View Post
    If you're time is free, the more you tear apart, the more you'll make in scrap. pretty simple.

    Aluminum average price .50/#
    Copper wire .75-.95/#
    Battery .25/#
    Alternator .25/#
    Starter .25/#


    figure out how fast you can do it, and see what's worth your time. The only time I play the "what's it worth" game is when I'm buying, once I have it, get it processed and gone. Put up a part out thread while you are tearing down. put up cheap prices, above scrap, below auto salvage price. what moves moves, what doesn't scrap.

    (I really shouldn't say anything because there is still some parts in the garage from my last partout.. in september. It's the same truck that I currently drive though, so I don't feel bad)
    Yeah, I understand what you are saying, but like I said I'm looking at selling it outright instead of scrapping it myself.

    Quote Originally Posted by corycouch View Post
    1st thanks skyline for the compliment

    2nd, I can't see me getting 200 for any set of tires, I had a new set of all terrains a year or so ago for $100. I get $10 a tire for good tires from my buyer, they sell them for $25. Tires for me is what's worth my time, I could get more, but that would mean dealing with dozens of phone calls and dozens of dumb@$$ questions about tires sooooo, I sell them to someone else. Bottom line I can buy a car in the time it takes to sell one set of tires or even worse waiting on a no show for two hours.

    3rd as for the take off stuff it will depend on your prices which will mainly depend on your relationship with your yard
    I've bought and sold tires a couple times.....
    In my dealing with near new used tires.... I bought 2 Deulers down in Florida for $60.... was going to put them on my VUE.... but then found a matching set of 4 tires in southern IN and sold the Deulers on CL for $150..... thus what I'm looking at price wise on selling them.... I am use to the idiots calling about CL postings but hay I'm fine with making $$$

    Quote Originally Posted by sledge42 View Post
    IF I were to be gutting that car this is the approximate math:
    $320 on body (this taking into car having a bunch removed)
    $100-$125 on Tires - and would cost me $12 to have removed
    Rims would be tossed back in the car
    $80: Converters total
    $7 on the Alternator
    $5 on A/C Pump
    $35 on Wiring
    $7 bucks if you get both heater cores and rads
    $5 or so in A/C lines, condenser etc
    $12 on Battery

    $559 to $584 Ballpark
    Profit $239 to $264 at $320 Buy Price.

    But as it has been said- your BEST learning "advice" is experience. Dig in, Gut her hard and see what she brings you!
    Thanks for rough estimates, I know that the best way to understand everything is to experience it myself.... but would rather wait and learn on something that i'm not going to make $$$ on if i sell it outright.... with that... is there a guide for about how much CATS are worth for all different cars?

    Thank you all for your time & help
    Once this snow goes.... I will be scrapping the SC2 and get a bit of an idea about everything

  19. #13
    corycouch's Avatar
    SMF Badges of Honor


    Member since
    Dec 2011
    Location
    jonesboro ar
    Posts
    1,405
    Thanks
    3,766
    Thanked 1,988 Times in 746 Posts
    Quote Originally Posted by saturninin View Post
    I completely understand the "different area different prices".... but i was just looking for a bit of guidance



    Yeah, I understand what you are saying, but like I said I'm looking at selling it outright instead of scrapping it myself.



    I've bought and sold tires a couple times.....
    In my dealing with near new used tires.... I bought 2 Deulers down in Florida for $60.... was going to put them on my VUE.... but then found a matching set of 4 tires in southern IN and sold the Deulers on CL for $150..... thus what I'm looking at price wise on selling them.... I am use to the idiots calling about CL postings but hay I'm fine with making $$$



    Thanks for rough estimates, I know that the best way to understand everything is to experience it myself.... but would rather wait and learn on something that i'm not going to make $$$ on if i sell it outright.... with that... is there a guide for about how much CATS are worth for all different cars?

    Thank you all for your time & help
    Once this snow goes.... I will be scrapping the SC2 and get a bit of an idea about everything

    ??????????????????? I may be reading to much into this but,
    1. You asked for our help
    2. You already had your answers before you heard our suggestions
    3. Then you ask another?

    I'm not trying to beat you up, but you can't go into a conversation asking a question, then contradict answers you receive. There is no right or wrong way to scrap a car as long as you stay in legal boundaries. The information I gave you as the others is from personal experience and we try to help everyone and when needed we ask for help ourselves. There's more id like to say but at this point I'm not wanting a vacation

  20. The Following 5 Users say Thank You for This Post by corycouch:


  21. #14
    saturninin started this thread.
    SMF Badges of Honor


    Member since
    Jul 2012
    Location
    Indiana
    Posts
    67
    Thanks
    8
    Thanked 39 Times in 17 Posts
    Quote Originally Posted by corycouch View Post
    ??????????????????? I may be reading to much into this but,
    1. You asked for our help
    2. You already had your answers before you heard our suggestions
    3. Then you ask another?

    I'm not trying to beat you up, but you can't go into a conversation asking a question, then contradict answers you receive. There is no right or wrong way to scrap a car as long as you stay in legal boundaries. The information I gave you as the others is from personal experience and we try to help everyone and when needed we ask for help ourselves. There's more id like to say but at this point I'm not wanting a vacation
    Reason I asked for the help was being unsure of what I thought about in my head... I had a rough idea of what I was going to expect from scrapping it but had no real experience at all in doing the actual task. I learn a lot from reading and trying to understand from others is the best way for me to look at things... and now being very thankful to everyone on this forum.... what I thought was correct... if i can sell the car for $750 and run, it is the best situation verses scrapping it out.

    The only thing that I felt confident about price wise is getting a bit more for the tires than what you were saying that you got (knowing that I will be setting on them for a while, also)

    I'm just trying to figure out a bit from others to make informed decisions on best for my situation to make the most $$$ on the car. I believe that the only real thing that I've contradicted on was the price on the tires, the rest is **much** valuable information that I thank y'all for

    The reason I asked about the CATS on other cars is so that I could get a rough estimate on what they are worth.... then (now that I have a rough idea on overall scrapping of the car) I can factor that in and know when it's better to CL a car (doing nothing on it) verses scrapping it

  22. #15
    Mechanic688's Avatar
    SMF Badges of Honor



    Member since
    Mar 2011
    Location
    Warsaw , Ind. In the heart of the lakes, and down the street from the hotel where Al Capone stayed.
    Posts
    9,568
    Thanks
    11,247
    Thanked 10,730 Times in 4,728 Posts
    with that... is there a guide for about how much CATS are worth for all different cars?
    This is not a recommendation but only for a picture guide, there's quite a few on Google.

    http://www.converterguys.com/index.p...verter-photos/
    P & M Recycling - Specializing in E-Waste Recycling.
    If you enjoy your freedom, thank a vet.

  23. The Following User Says Thank You to Mechanic688 for This Post:


  24. #16
    ocedy's Avatar
    SMF Badges of Honor


    Member since
    Apr 2011
    Location
    Houston
    Posts
    116
    Thanks
    5
    Thanked 52 Times in 29 Posts
    I wilo say this good score. First ask yourself how quick do you want to recap your money. Here goes if you part out you should clear 500 to 700. If the battery is good you can sell for 25 to 30 but the need to bring you the old battery. Next it should have 4 cats @ around 100 for all. Tranny 200 with core. Rad heater core 25. Wires 20. You sell the interior stuff on ebay. Light switches, ac controlls, window switches, taillights etc. 200 to 300. Once stripped take the rest to yard about 200. Good luck

  25. The Following User Says Thank You to ocedy for This Post:


  26. #17
    WoodmanYoel's Avatar
    SMF Badges of Honor


    Member since
    Dec 2013
    Posts
    98
    Thanks
    10
    Thanked 93 Times in 37 Posts

  27. The Following User Says Thank You to WoodmanYoel for This Post:



  28. Similar threads on the Scrap Metal Forum

    1. home made work bench and tool charging station
      By msearl3244 in forum Made From Scrap
      Replies: 0
      Last Post: 07-01-2013, 09:48 AM
    2. 1994 Ford Taurus V6- Is there a Pre-Converter?
      By sledge in forum Vehicle Recycling
      Replies: 19
      Last Post: 04-30-2013, 07:17 AM
    3. 1950s Ford Water Heater. What is it made out of?
      By beedubz in forum Scrap Metal Identification
      Replies: 5
      Last Post: 04-22-2013, 10:33 AM
    4. Honey Wagon
      By gustavus in forum Off Topic Discussions
      Replies: 11
      Last Post: 09-25-2011, 12:01 AM
    5. This made me smile. Scrap metal made the front page today
      By wdaddy in forum Off Topic Discussions
      Replies: 3
      Last Post: 08-23-2011, 06:33 PM

Thread Information

Users Browsing this Thread

There are currently 6 users browsing this thread. (0 members and 6 guests)

 
Browse the Most Recent Threads
On SMF In THIS CATEGORY.





OR

Bookmarks

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •  

The Scrap Metal Forum

    The Scrap Metal Forum is the #1 scrap metal recycling community in the world. Here we talk about the scrap metal business, making money, where we connect with other scrappers, scrap yards and more.

SMF on Facebook and Twitter

Twitter Facebook