Printable View
hey Folks this is Mr Scrapper.. Got a good educational video about what you need to be a succesful Pc Scrapper..Enjoy the video..
http://s1307.photobucket.com/user/bn...53e69.mp4.html
If You've any question please feel free to contact Me. .I"m more then willing to help.
Thanks for checking out our Common Tools for Scrappin
did not see any tools on my computer for some reason but this I saw , I heard about those chips - Gold Gold Gold
My main scrap weapon of choice is my snip/cutter and my drill.Quote:
Originally Posted by pcscrapper
Thanks for the video, Larry. Always good to see a good sized operation at work.
I have a question. At your hard drive bench, where is your bin for hard drive magnets? LOL. Had to ask that.
Quote:
Originally Posted by pcscrapper
I Really appreciate your post,it is very nice of you offer such a great view of your big operation.
Much obliged.
ginofrater
Yooo Man... want a Hit... Got it right here to the right of da bench dude... Ahhhhh yeahhhhh baby smooth... as its goes.. smoooooth as it goes..Quote:
Originally Posted by parrothead
Now I'm gonna have to Kilz you yahlll.... slowly.. with My band saw... small pieces shall do.. sayyyyyQuote:
Originally Posted by ginofrater
I really like your disassembling bench. If I was going to make one, what do you think about making a shoot underneath the mesh that would funnel all of the bits into a container? It might have to be a considerable grade so things don't get stuck...
We did attempt it,,, the problem is... if you drop a bit... or a drill bit or what ever you drop thru the mesh.. guess what Your're gonna be going under that bench quite offten.. as We found out.. so We decided not to do that anymore and just fish the bit out from the top thru the mesh..
I hope that answer your question.
Yeah it does, thank you. That is something I hadn't considered.
Please don't drive!!!:-oQuote:
Originally Posted by pcscrapper
I don't drive.. I FLY Baby FLy....Quote:
Originally Posted by ginofrater
You should not post in this condition.Quote:
Originally Posted by pcscrapper
I will not consider your posts in the future.
Sorry.
Ok... I'm sorry that I can fly an airplane... a single engine .. but.. you stated Don't drive.. concern.? why you upset with me.Quote:
Originally Posted by ginofrater
sorry if I offended You in a way that hurt your feeling.. but I was stating the fact.. I didn't take your comment offensive..
I took it as a comment.
Did I offend anyone with a post about Me me sayin I fly baby Fly..?
I have GOT to sit down and figure out how to redo this bench in a way that works for me!
Give me a pm and I'll answer any quesiton that you may have.
We're always making tweaks to our bench.
I've to say this is on the best bench I builted. Its easy to clean out.. and the wire mesh has taken such a beating.. it still perfect.
Look forward to helping You.
Did You git one figured out.. Was thinking but again.. if You drop a bit or sumthing it gonna be a pain to get it out.. but may work..Quote:
Originally Posted by Electrowaste
Build your bench flat... like I did.. put a access panel from the side to the other side but build a frame box on the bottom side of the table.. and then make yourself a tounge and groove slot in that box frame you builted. then what You can do.. is you would need a broom that would be so wide that will be able to fit in between the two by fours and push your screws and such into the drop box and then pull the board out of the tounge n groove for the screws to fall into a bin the width of the table. but before you put your mesh on top.. put several two by fours at the dead end of the able.. drill holes into them that would allow a push broom stick to be scrwed into.. and again when ready to you can slide your broom handle in.. turn it in.. and then pull the screws toward the drop down area for the opening on the bottom of the table.. think that would work better Might have to do that.. next time I do a clean out.